480927
9
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0782 EN
Copyright © 2015 VARO P a g e | 9 www.varo.com
9 INSTALLATION AND TRANSPORT
Do not carry the machine on the handgrip; the handgrip is not designed to
carry the full weight of the machine. For carrying the machine, hold it on
both edges of the base (12).
9.1 Installation (Fig. 14)
Get help from another person for lifting the machine out of the box.
Turn the turntable into the 0° position and tighten up the mitre locks.
Note:
If the machine must be mounted on a workbench, then the rubber feet should NOT be
installed.
To install the rubber feet, turn the machine carefully to the right, so that it is supported by
the motor.
Insert the nut (A3) in the hole at the lower side of the rubber feet.
Insert the main socket screw (A1) in the machine at the upper side. Fasten the rubber feet
(A2) with the previously inserted nut (A3) to screw (A1).
Only use your hands for tightening the rubber feet.
Use the hexagonal spanner for tightening the screw.
You run the risk of injury, if you handle the machine incorrectly when lifting
or turning it. Always hold the machine firmly by the base (12).
Position the machine on a suitable surface:
- All 4 feet must rest firmly on the surface.
- The ideal height of the surface is approximately 800 mm.
- The saw must stand firmly in position, even when larger workpieces are being sawn.
You can keep the packaging for future use, or you can dispose of it separately, based on
the type of material, and it in an environmentally friendly manner.
9.2 Transport (Fig. 5, 12, 13)
Position the lowest saw blade guard (14) over the saw guide piece (21) and push
backwards until you hear a click, and until he saw blade protector is positioned at the
black line on the saw guide piece.
Lower the saw head by pushing in the safety lock (6) and activate the locking pin (22).
Position the mitre guide (4) over the saw blade guard and fasten it.
Lift the machine up by grasping both sides of the base (12).
Note:
The essential operating components of the machine are presented in this section.
Make sure to read this section, before you use the machine for the first time.
9.2.1 Table saw operating mode (Fig. 2, 5, 6, 12)
Make sure that the table is mounted completely and in the right direction (Fig. 2) see
Paragraph 7.1 on Transport above - and that the locking pin (22) is properly locked.
Remove the mitre and width guide (4).
The ON/OFF switch (7) is used for starting and stopping the machine.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0782 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0782 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0782

Powerplus POWX0782 User Manual - German - 24 pages

Powerplus POWX0782 User Manual - Dutch - 23 pages

Powerplus POWX0782 User Manual - French - 24 pages

Powerplus POWX0782 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info