677891
9
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 9 www.varo.com
Make sure that the turn table is fixed securely.
Make sure that the arm is securely fixed in the working position. Tighten the lever
clockwise to fix the arm.
Use (6) push stick or (6) push block to avoid working with the hands and fingers close to
the saw blade.
Make sure the blade is not contacting the riving knife or workpiece before the switch is
turned on.
Always store the push-stick when it is not in use.
Pay particular attention to instructions for reducing risk of KICKBACK. KICKBACK is (6)
sudden reaction to (6) pinched, bound or misaligned saw blade. KICKBACK causes the
ejection of the workpiece from the tool back towards the operator. KICKBACKS CAN
LEAD TO SERIOUS PERSONAL INJURY. Avoid KICKBACKS by keeping the blade
sharp, by keeping the rip fence parallel to the blade, by keeping the riving knife and blade
guard in place and operating properly, by not releasing the workpiece until you have
pushed it all the way past the blade, and by not ripping (6) workpiece that is twisted or
warped or does not have (6) straight edge to guide along the fence.
Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard workpieces. Do
not bend or twist workpiece while feeding. If you stall or jam the blade in the workpiece,
turn the tool off immediately. Unplug the tool. Then clear the jam.
Before turning over the tool, always make sure that the stopper pin has securely locked
the tool head in the lowest position.
7 INSTALLATION
CAUTION: Keep the floor area around the tool level, well maintained and
free of loose materials e.g. chips and cut-offs.
7.1 Bench mounting (Fig. 1 & 3)
7.1.1 For the fully-extended feet set up as the high table.
When the tool cannot be set up stable, turn the adjusting nut at the foot of the tool for proper
stability. Turn counterclockwise in top viewing to make the foot shorter and clockwise in top
viewing to make it longer. After adjustment, make sure that the tool keep stable.
7.1.2 For the folded feet set up as the low table
When the tool is ready in the foot-folded position, secure the tool by using U-shaped grooves
shown in the figure. (fig 3 (5) )
8 FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and unplugged
before adjusting or checking function on the tool.
8.1 Blade guard (Fig. 4, 5 & 6)
Caution:
Make sure that the handle cannot be lowered without pushing the lever nearby the handle
to the left. (fig 2 - 20)
Make sure that the lower blade guards A dose not open unless the lever near the handle
is pushed at the topmost position of the handle.
Make sure that the lower blade guard C is installed before using in Mitre saw mode.
When lowering the handle while pushing the lever to the left, the lower blade guard A rises
automatically. The lower blade guard B rises as it contacts a workpiece. The lower blade
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info