677891
7
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 7 www.varo.com
If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of these devices can reduce dust related
hazards.
5.4 Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools. Check for misalignment or sticking of moving parts, breakage of
parts and any other condition that may affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to stick and are easier to control.
Use the power tool, accessories and tool bits etc., in accordance with these instructions
and in the manner intended for the particular type of power tool, taking into account the
working conditions and the work to be performed. Use of the power tool for operations
different from intended could lead to a hazardous situation.
5.5 Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
6 ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS
6.1 For both Mitre saw mode and table saw (bench saw) mode:
Wear eye and hearing protection. Other suitable personal protective equipment should be
worn.
NEVER wear gloves during operation except for replacing saw blades or handling rough
material before operation.
Keep the floor area around the tool level, well maintained and free of loose materials e.g.
chips and cut-offs.
Do not operate saw without guards and riving knife in place. Check blade guards for
proper closing before each use. Do not operate saw if blade guards do not move freely
and close instantly. Never clamp or tie the blade guards into the open position. Any
irregular operation of the blade guards should be corrected immediately.
Clean and be careful not to damage the spindle, flanges (especially the installing surface)
and hex bolt before or when installing the blade. Damage to these parts could result in
blade breakage. Poor installation may cause vibration/ wobbling or slippage of the blade.
Use only flanges specified for this tool.
Check the blade carefully for cracks or damage before operation. Do not use saw blade
which are damaged or deformed.
Use only saw blades recommended by the manufacturer and which conform to EN847-1,
and observe that the riving knife must not be thicker than the width of the cut by the saw
blade and not thinner than the body of the blade.
Always use accessories recommended in this manual. Use of improper accessories such
as abrasive cut-off wheels may cause an injury.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info