675011
13
Zoom out
Zoom in
Previous page
1/19
Next page
POWX07551T EN
Copyright © 2016 VARO P a g e | 13 www.varo.com
8.16 Maximum cutting depth (Fig. 19)
The maximum depth travel of the cutting head was set at the factory. Check to see that the blade
does not extend more than 1/4 in. below the table insert, and does not touch the control arm
throat or any part of the base or table. If the maximum depth needs readjusting:
Loosen the bolts of the stop plate (2).
Move the cutting head down until the blade extends just 1/4 in. below the table insert.
Adjust the stop place to touch the bottom of the stop knob (1) when the stop knob is raised
fully.
Recheck the blade depth by moving the cutting head front to back through the full motion
of a cut along the control arm. If the blade touches the inside of the control arm, readjust
the setting.
8.17 The laser guide (Fig. 20)
WARNING! For your own safety, never connect the plug to a power source
outlet until all the adjustment steps are complete and you have read and
understood the safety and operational instructions.
Your tool is equipped with a laser guide using a Class IIIa laser beam. The laser beam will
enable you to preview the saw blade path on the workpiece to be cut before starting the mitre
saw. This laser guide is powered by two AAA 1.5 volt batteries.
To turn laser on, press on/off rocker switch (1) to “ON” position.
To turn laser off, press on/off rocker switch to “OFF” position.
NOTE: All the adjustments for the operation of this laser guide have been
completed at the factory. Laser guide is calibrated and set up to project to
the right of the blade.
WARNING! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
WARNING! The use of optical instruments with this product will increase
eye hazard. Do not attempt to repair or disassemble the laser. If unqualified
persons attempt to repair this laser product, serious injury may result. Any
repair required on this laser product should be performed by authorized
service center personnel.
9 OPERATION
9.1 Basic saw operations
9.1.1 Turning the laser guide on (Fig. 21)
Press the on/off rocker switch (1) to “ON” position to activate the laser guide.
9.1.2 Turning the saw on (Fig. 21)
This mitre saw is equipped with an ON/OFF trigger switch (2). With the safety lock (3) pressed,
squeeze the trigger switch to turn the mitre saw ON. When the trigger switch is released, the
blade will be stopped within 10 seconds.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07551T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07551T in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07551T

Powerplus POWX07551T User Manual - German - 21 pages

Powerplus POWX07551T User Manual - Dutch - 21 pages

Powerplus POWX07551T User Manual - French - 21 pages

Powerplus POWX07551T Additional guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info