Manual Powerplus POWX07551T (page 12 of 19) (English)

675011

Zoom out

Zoom in

1/19

POWX07551T EN

8.12.3 45° Bevel adjustment (Fig. 16)

 Loosen the bevel lock handle (1) and tilt the cutting head completely to the left.

 Using a combination square, check to see if the blade angle is 45° to the table.

 If the blade is not at 45° to the mitre table, tilt the cutting arm to the right, loosen the

locknut (2) on the bevel angle adjustment bolt (3) and use a 10 mm wrench to the

adjustment bolt (3) depth in or out to increase or decrease the bevel angle.

 Tilt the cutting arm to the left to 45° bevel and recheck for alignment.

 Repeat steps 1 through 4 until the blade is at 45° to the mitre table.

 Tighten bevel lock handle (1) and locknut (2) when alignment is achieved.

8.13 Mitre scale (Fig. 17)

The sliding compound mitre saw scale can be easily read, showing mitre angles from 0° to 45° to

the left, and 0° to 45° to the right. The mitre saw table has nine of the most common angle

settings with positive stops at 0°, 15°, 22.5°, 31.6°, and 45°. These positive stops position the

blade at the desired angle quickly and accurately. Follow the process below for quickest and

most accurate adjustments.

8.13.1 To adjust mitre angles

 Unlock the mitre table by turning the mitre handle (1) counterclockwise.

 Move the turntable while lifting up on the positive stop locking lever (2) to align the

indicator (3) to the desired degree measurement.

 If the desired angle is one of the nine positive stops, release the positive stop locking

lever, making sure the lever snaps into position, and then secure by tightening the mitre

handle.

 If the mitre angle desired is not one of the nine positive stops, simply lock the mitre table

into desired angle position by turning the mitre handle in the clockwise direction.

8.13.2 Mitre angle pointer adjustment

 Move the table to the 0° positive stop.

 Loosen the screw (4) that holds the indicator with a Phillips screwdriver.

 Adjust the indicator (3) to the 0° mark and retighten the screw.

8.14 Adjusting fence squareness (Fig. 18)

 Lower the cutting arm and lock in position.

 Loosen the two fence locking bolts (1) with an 8 mm hex wrench.

 Using a square (3), lay the heel of the square against the blade and the ruler against the

fence (2) as shown.

 Adjust the fence 90° to the blade and tighten the four fence locking bolts.

NOTE: If the saw has not been used recently, recheck blade squareness to

the fence and readjust if needed.

 After fence has been aligned, make a cut at 90° using a scrap piece of wood and check

squareness on the piece. Readjust if necessary.

8.15 Setting cutting depth (Fig. 19)

The depth of cut can be preset for even and repetitive shallow cuts.

 Adjust the cutting head down until the teeth of the blade are at the desired depth.

 While holding the upper arm in that position, turn the stop knob (1) until it touches the stop

plate (2).

 Recheck the blade depth by moving the cutting head front to back through the full motion

of a typical cut along the control arm.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07551T in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07551T

Powerplus POWX07551T User Manual - German - 21 pages

Powerplus POWX07551T User Manual - Dutch - 21 pages

Powerplus POWX07551T User Manual - French - 21 pages

Powerplus POWX07551T Additional guide - All languages - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX07551T Manual

Product: