675011
9
Zoom out
Zoom in
Previous page
1/19
Next page
POWX07551T EN
Copyright © 2016 VARO P a g e | 9 www.varo.com
8.8 Removing and installing the table insert (Fig. 7)
NOTE: The mitre saw comes with the table inserts already installed. These
instructions are for replacing or adjusting either insert side.
WARNING! To avoid injury: 1) Always unplug the saw to avoid accidental
starting. Remove all small pieces of material from the table cavity before
performing any cuts. The table insert may be removed for this purpose, but
always reattach the table insert prior to performing a cutting operation. 2)
Do not start the sliding compound mitre saw without checking for
interference between the blade and table insert. Damage could result to the
blade, table insert or turntable if blade strike occurs during the cutting
operation.
To remove, loosen and remove the six screws (1) on the table insert (2) with a Phillips
screwdriver and remove the insert.
To install, reposition the table insert, install the six screws and tighten.
Check for blade clearance by moving the slide carriage through the full motion of the blade
in the table slot. If neither side of the insert hits the saw blade, loosen the three screws for
that side and adjust. Tighten the screws and check again for blade clearance.
8.9 Mounting the mitre saw (Fig. 8 ,9, 10)
WARNING! To avoid injury from unexpected saw movement: 1) Disconnect
the power cord from the outlet and lock the cutting head in the lower
position using the stop latch. 2) Lock the slide carriage in place by
tightening the slide carriage lock knob. 3) To avoid back injury, lift the saw
by using the hand holds for transportation. Bend with your knees, not your
back. 4) Never carry the mitre saw by the power cord or by the switch
handle. Carrying the tool by the power cord could cause damage to the
insulation or the wire connections resulting in electric shock or fire. 5) To
avoid injury from flying debris, do not allow visitors to stand near the saw
during any cutting operations.
Mounting instructions:
For stationary use, place the saw in the desired location, directly on a workbench where
there is room for handling and proper support of the workpiece. The base of the saw has
four mounting holes (10 - Fig. 8). Bolt the base of the mitre saw (1) to the work surface (5),
using the recommended fastening method as shown in Fig. 9.
1. Mitre saw base
2. Hex head bolt
3. Rubber washer
4. Flat washer
5. Work surface
6. Flat washer
7. Lockwasher
8. Hex/Lock nut
9. Jam nut
NOTE: Mounting hardware is not included with this tool. Bolts, nuts,
washers and screws must be purchased separately.
For portable use, place the saw on a 3/4 in. thick piece of plywood. Bolt the base of the
mitre saw securely to the plywood using the mounting holes (10 - Fig. 8) on the base. Use
C-clamps to clamp this mounting board to a stable work surface at the worksite. (Fig. 10)
NOTE: If the mitre saw stand is used, please mount it as shown in FIG. B.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07551T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07551T in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07551T

Powerplus POWX07551T User Manual - German - 21 pages

Powerplus POWX07551T User Manual - Dutch - 21 pages

Powerplus POWX07551T User Manual - French - 21 pages

Powerplus POWX07551T Additional guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info