645072
8
Zoom out
Zoom in
Previous page
1/10
Next page
POWX05201 EN
Copyright © 2016 VARO P a g e | 1 www.varo.com
1 APPLICATION .................................................................................. 3
2 DESCRIPTION (FIG. A) ................................................................... 3
3 PACKAGE CONTENT LIST ............................................................. 3
4 MBOLS ............................................................................................. 4
5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4
5.1 Work area ................................................................................................................ 4
5.2 Electrical safety ....................................................................................................... 4
5.3 Personal safety ....................................................................................................... 5
5.4 Power tool use and care ......................................................................................... 5
5.5 Service ..................................................................................................................... 5
6 SPECIFIC SAFETY WARNINGS FOR CIRCULAR SAWS............. 6
7 ASSEMBLY ...................................................................................... 6
7.1 Replacing the saw blade (Fig. 1) ............................................................................ 6
7.2 Depth adjustment (Fig. 2) ....................................................................................... 6
7.3 Angle adjustment (Fig. 3) ....................................................................................... 7
7.4 Switching on and off(Fig.4) .................................................................................... 7
7.5 Parallel cut adjustment(Fig.5) ................................................................................ 7
8 OPERATION ..................................................................................... 7
8.1 General cutting ........................................................................................................ 7
8.2 Pocket cutting ......................................................................................................... 7
8.3 Cutting Large Sheets .............................................................................................. 7
9 CLEANING AND MAINTENANCE ................................................... 8
9.1 Cleaning................................................................................................................... 8
9.2 Lubrication .............................................................................................................. 8
10 TECHNICAL DATA .......................................................................... 8
11 NOISE ............................................................................................... 8
12 SERVICE DEPARTMENT ................................................................ 9
13 STORAGE ........................................................................................ 9
14 WARRANTY ..................................................................................... 9
15 ENVIRONMENT ............................................................................. 10
POWX05201 EN
Copyright © 2016 VARO P a g e | 2 www.varo.com
16 DECLARATION OF CONFORMITY .............................................. 10
POWX05201 EN
Copyright © 2016 VARO P a g e | 3 www.varo.com
CIRCULAR SAW 1200W 185MM
POWX05201
1 APPLICATION
Your circular saw has been designed for sawing wooden workpieces. The machine is only
suitable for right-hand use. The machine is not suitable for stationary use.
It is not designed for commercial use.
WARNING! Read this manual and general safety instructions carefully
before using the appliance, for your own safety. Your power tool should
only be passed on together with these instructions.
2 DESCRIPTION (FIG. A)
1. Lever of lower guard
2. Dust extraction outlet
3. Saw blade
4. Depth gauge
5. Guide handle
6. Bevel scale bracket
7. Lock level for depth adjustment
8. Lock knob for angle adjustment
9. Lock knob for parallel guide
10. Base plate
11. Parallel guard
12. Lower guard
13. Blade clamp bolt
14. Outer flange
15. Spindle lock button
16. On/off switch
17. Lock-off button
18. Main handle
3 PACKAGE CONTENT LIST
Remove all packing materials
Remove remaining packaging and transit supports (if existing)
Check the completeness of the packing content
Check the appliance, the power cord, the power plug and all accessories for transportation
damages.
Keep the packaging materials as far as possible till the end of the warranty period.
Dispose it into your local waste disposal system afterwards.
WARNING Packing materials are no toys! Children must not play with
plastic bags! Danger of suffocation!
1x allen key
1x manual
1x dust pipe
1x guide bar
1x saw blade
When parts are missing or damaged, please contact your dealer.
POWX05201 EN
Copyright © 2016 VARO P a g e | 4 www.varo.com
4 MBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal
injury or damage to the
tool.
In accordance with essential
requirements of the European
directive(s).
Read manual before use.
"Class II - The machine is double
insulated; Earthing wire is
therefore not necessary.
Always wear protective
gloves
Always wear safety goggles
5 GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and all instructions. Failure to follow all warnings and instructions
may result in electric shock, fire and/or serious injury. Save all warnings and instructions for
future reference. The term "power tool" in the warnings refers to your mains operated (corded)
power tool or battery operated (cordless) power tool.
5.1 Work area
Keep work area clean and well lit. Cluttered and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
5.2 Electrical safety
Always check that the power supply corresponds to the voltage on the
rating plate.
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
POWX05201 EN
Copyright © 2016 VARO P a g e | 5 www.varo.com
5.3 Personal safety
Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious
personal injury.
Use safety equipment. Always wear eye protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used whenever conditions require
will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have
the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of these devices can reduce dust related
hazards.
5.4 Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools. Check for misalignment or sticking of moving parts, breakage of
parts and any other condition that may affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to stick and are easier to control.
Use the power tool, accessories and tool bits etc., in accordance with these instructions
and in the manner intended for the particular type of power tool, taking into account the
working conditions and the work to be performed. Use of the power tool for operations
different from intended could lead to a hazardous situation.
5.5 Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
POWX05201 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
6 SPECIFIC SAFETY WARNINGS FOR CIRCULAR SAWS
Make sure that all devices screening the saw blade are in perfect working order.
Make sure that the saw blade is screened correctly. Especially observe the following
instructions:
Never block the saw blade guard. Repair a jammed saw blade guard before using the
machine again.
Replace a broken tension spring before using the machine again.
Never remove the riving knife. The distance between the toothed rim and the riving knife
should be 5 mm maximum. The height difference between the riving knife and the
toothed rim should be 5 mm maximum.
Do not use saw blades made of HSS steel.
Do not use bent, deformed or otherwise damaged saw blades.
Do not use saw blades which do not meet the specifications stated in this manual.
Before sawing, remove all nails and other metal objects from the workpiece.
Never start sawing before the saw reaches its full speed.
Securely clamp the workpiece. Never attempt to saw extremely small workpieces.
Only put the machine aside after switching off and when the saw blade has come to a
complete standstill.
Never try to slow the saw blade down by exerting pressure on the side.
Before performing maintenance to the machine, always unplug the machine.
7 ASSEMBLY
7.1 Replacing the saw blade (Fig. 1)
Only use sharp and undamaged saw blades. Cracked or bent saw blades must be replaced
immediately.
Place this circular saw on its side on a flat surface. Advice you bring the base plate (10)
down as if a minimum depth cut which is ease to operate change the blade.
Push the spindle lock button toward motor housing as the arrow shows in Fig. 1 and firmly
hold it.
Turn the blade clamp bolt anti-clockwise by using the spanner the hex key that supplied
with the tool.
Remove the blade clamp bolt and outer flange.
Raise the lower guard (12) by using the lever for lower guard (1), and then remove the
saw blade.
Clean the saw blade flanges, then mount the new saw blade onto the output spindle and
against the inner flange.
Make sure the saw teeth and arrow on the blade is to be the same direction as the arrow
on the lower guard.
Reinstall the outer flange, and tighten the blade clamp bolt.
Make sure that the saw blade runs freely by turning the blade by hand.
Before replacing the saw blade always unplug the tool.
7.2 Depth adjustment (Fig. 2)
Loosen the adjusting screw lock lever for depth adjustment (7).
Hold the base plate (10) flat against the edge of the work piece and lift the body of the saw
until the blade is at the right depth determined by the depth gauge of cut scale (4) (align
the scale line).
Tighten the adjusting screw the lock lever for depth adjustment.
POWX05201 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
7.3 Angle adjustment (Fig. 3)
Loosen the lock lever knob for angle adjustment (8).
Adjust the base plate to the desired angle between 0° to 45°. [See Scale for mitre angle
(8)].
Tighten the lock lever knob for angle adjustment.
7.4 Switching on and off(Fig.4)
Before engage the ON/OFF switch, check that the saw blade is properly
fitted and run smoothly, the blade clamp bolt is well tightened.
Connect the plug to the power supply.
To switch on the circular saw, press the lock-off button (17) and pull the ON/OFF switch
trigger (16).
When you release the switch trigger (16), the tool turns off.
7.5 Parallel cut adjustment(Fig.5)
Loosen the lock knob of parallel guide (9).
Slide the parallel guide (11) through the slots in the shoe to the desired width.
Tighten the lock bolt to fit it in the position.
Ensure that the edge guide rests against the wood along its entire length to give a
consistent parallel cuts.
8 OPERATION
8.1 General cutting
When starting, always hold the saw handle with one hand and the auxiliary handle (5) with
the other hand. Never force the saw but maintain a light and continuous pressure after
completing the cut allow the saw to come to a complete stop. When cutting is interrupted,
resume cutting by allowing the blade to reach full speed and then reentering the cut
slowly.
When cutting across the grain, the fibers of the wood have a tendency to lift and tear,
moving the saw slowly minimizes this effect.
8.2 Pocket cutting
Disconnect the plug from the power supply before making any adjustments. Set the depth
adjustment based on the thickness of the line drawing for the cut .raise the lower guard by
using the lift lever.
With the blade barely above the material to be cut, start the saw and allow the blade to
come to full speed. Gradually lower the blade unto the material to be cut using the front
end of the shoe as a pivot point. When the blade starts cutting, release the lower guard.
When the shoe is resting flat on the surface being cut, proceed cutting in a forward
direction to the end of the cut. Allow the blade to come to a full stop before removing it
from the cut. Never pull the saw backward since the blade will climb out of the cut and
kickback will occur. Turn the saw around and finish the cut in a normal manner, sawing
forward. Use a jigsaw or a hand saw to finish the cut in the corners, if required.
8.3 Cutting Large Sheets
Large sheet or boards require support to prevent bends or sags. If you attempt to cut
without leveling and properly supporting the work piece, the blade will tend to bind,
causing kickback.
Support the panel or board close to the cut. Be sure to set the blade adjustment so that
you can cut through the material without cutting into the table or workbench. Suggestion:
use two by fours to support the board or panel to be cut. If the piece is too large for the
workbench, use the floor with the two-by fours supporting the wood.
POWX05201 EN
Copyright © 2016 VARO P a g e | 8 www.varo.com
9 CLEANING AND MAINTENANCE
Attention !Before performing any work on the equipment, pull the power
plug.
9.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
9.2 Lubrication
From time to time, apply a drop of oil to the thread of the lock screw.
10 TECHNICAL DATA
Rated voltage
220-240V
Rated frequency
50Hz
Rated power
1200W
Rotation speed
5800min
-1
Blade diameter
185mm
Cable length
2m
Max cutting capacity 90°
62mm
Max cutting capacity 45°
46mm
Cutting depth: wood
62/46mm
Bore size
16mm
Adjustable angle
Yes
Number of teeth
24T
Blade dimensions
185 x 16mm
Upper guard
Nylon
Base plate
Stamped steel
Base material
Steel
Second handle type
Guide handle
11 NOISE
Noise emission values measured according to relevant standard. (K=3)
Acoustic pressure level LpA
Acoustic power level LwA
ATTENTION! Wear hearing protection when sound pressure is
over 85 dB(A).
aw (Vibration)
3.2 m/s²
K = 1.5 m/s²
POWX05201 EN
Copyright © 2016 VARO P a g e | 9 www.varo.com
12 SERVICE DEPARTMENT
Damaged switches must be replaced by our after-sales service department.
If the connecting cable (or mains plug) is damaged, it must be replaced by a particular
connecting cable which is available from our service department. Replacement of the
connecting cable must only be carried out by our service department (see last page) or by
a qualified person (qualified electrician).
13 STORAGE
Thoroughly clean the whole machine and its accessories.
Store it out of the reach of children, in a stable and secure position, in a cool and dry
place, avoid too high and too low temperatures.
Protect it from exposure to direct sunlight. Keep it in the dark, if possible.
Don’t keep it in plastic bags to avoid humidity build-up.
14 WARRANTY
This product is warranted for a 36-month period effective from the date of purchase by the
first user.
This warranty covers all material or production flaws excluding : batteries, chargers,
defective parts subject to normal wear & tear such as bearings, brushes, cables, and
plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects
resulting from maltreatment, accidents or alterations; nor the cost of transportation.
Damage and/or defects resulting from inappropriate use also do not fall under the
warranty provisions.
We also disclaim all liability for any bodily injury resulting from inappropriate use of the
tool.
Repairs may only be carried out by an authorised customer service centre for Powerplus
tools.
You can always obtain more information at the number 00 32 3 292 92 90.
Any transportation costs shall always be borne by the customer, unless agreed otherwise
in writing.
At the same time, no claim can be made on the warranty if the damage of the device is the
result of negligent maintenance or overload.
Definitely excluded from the warranty is damage resulting from fluid permeation, excessive
dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate
usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not
following the instructions given in the manual), inexpert assembly, lightning strike,
erroneus net voltage. This list is not exhaustive.
Acceptance of claims under warranty can never lead to the prolongation of the warranty
period nor commencement of a new warranty period in case of a device replacement.
Devices or parts which are replaced under the warranty therefore remain the property of
Varo NV.
We reserve the right to reject a claim whenever the purchase cannot be verified or when it
is clear that the product has not been properly maintained. (Clean ventilation slots, carbon
brushes serviced regularly, etc.).
Your purchase receipt must be kept as proof of date of purchase.
Your appliance must be returned undismantled to your dealer in an acceptably clean state,
(in its original blow-moulded case if applicable to the unit), accompanied by proof of
purchase.
POWX05201 EN
Copyright © 2016 VARO P a g e | 10 www.varo.com
15 ENVIRONMENT
Should your appliance need replacement after extended use, do not discard it
with the household rubbish but dispose of it in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal
household rubbish. Please recycle where recycle facilities exist. Check with your
Local Authority or retailer for recycling advice.
16 DECLARATION OF CONFORMITY
VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,
product: Circular saw
trade mark: POWERplus
model: POWX05201
is in conformity with the essential requirements and other relevant provisions of the applicable
European Directives, based on the application of European harmonized standards. Any
unauthorized modification of the apparatus voids this declaration.
European Directives (including, if applicable, their amendments up to the date of signature);
2011/65/EU
2004/108/EC
2006/42/EC
European harmonized standards (including, if applicable, their amendments up to the date of
signature);
EN60745-1: 2009
EN60745-2-5: 2010
EN55014-1: 2006
EN55014-2: 1997
EN61000-3-2: 2014
EN61000-3-11: 2013
Keeper of the Technical Documentation : Philippe Vankerkhove, VARO Vic. Van Rompuy
N.V.
The undersigned acts on behalf of the company CEO,
Hugo Cuypers
Regulatory Affairs Compliance Manager
05/01/2016
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX05201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX05201 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX05201

Powerplus POWX05201 User Manual - German - 11 pages

Powerplus POWX05201 User Manual - Dutch - 11 pages

Powerplus POWX05201 User Manual - French - 11 pages

Powerplus POWX05201 Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info