Manual Powerplus POWX05201 (page 7 of 10) (English)

645072

Zoom out

Zoom in

1/10

POWX05201 EN

7.3 Angle adjustment (Fig. 3)

 Loosen the lock lever knob for angle adjustment (8).

 Adjust the base plate to the desired angle between 0° to 45°. [See Scale for mitre angle

(8)].

 Tighten the lock lever knob for angle adjustment.

7.4 Switching on and off(Fig.4)

Before engage the ON/OFF switch, check that the saw blade is properly

fitted and run smoothly, the blade clamp bolt is well tightened.

 Connect the plug to the power supply.

 To switch on the circular saw, press the lock-off button (17) and pull the ON/OFF switch

trigger (16).

 When you release the switch trigger (16), the tool turns off.

7.5 Parallel cut adjustment(Fig.5)

 Loosen the lock knob of parallel guide (9).

 Slide the parallel guide (11) through the slots in the shoe to the desired width.

 Tighten the lock bolt to fit it in the position.

 Ensure that the edge guide rests against the wood along its entire length to give a

consistent parallel cuts.

8 OPERATION

8.1 General cutting

 When starting, always hold the saw handle with one hand and the auxiliary handle (5) with

the other hand. Never force the saw but maintain a light and continuous pressure after

completing the cut allow the saw to come to a complete stop. When cutting is interrupted,

resume cutting by allowing the blade to reach full speed and then reentering the cut

slowly.

 When cutting across the grain, the fibers of the wood have a tendency to lift and tear,

moving the saw slowly minimizes this effect.

8.2 Pocket cutting

 Disconnect the plug from the power supply before making any adjustments. Set the depth

adjustment based on the thickness of the line drawing for the cut .raise the lower guard by

using the lift lever.

 With the blade barely above the material to be cut, start the saw and allow the blade to

come to full speed. Gradually lower the blade unto the material to be cut using the front

end of the shoe as a pivot point. When the blade starts cutting, release the lower guard.

When the shoe is resting flat on the surface being cut, proceed cutting in a forward

direction to the end of the cut. Allow the blade to come to a full stop before removing it

from the cut. Never pull the saw backward since the blade will climb out of the cut and

kickback will occur. Turn the saw around and finish the cut in a normal manner, sawing

forward. Use a jigsaw or a hand saw to finish the cut in the corners, if required.

8.3 Cutting Large Sheets

 Large sheet or boards require support to prevent bends or sags. If you attempt to cut

without leveling and properly supporting the work piece, the blade will tend to bind,

causing kickback.

 Support the panel or board close to the cut. Be sure to set the blade adjustment so that

you can cut through the material without cutting into the table or workbench. Suggestion:

use two by fours to support the board or panel to be cut. If the piece is too large for the

workbench, use the floor with the two-by fours supporting the wood.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX05201 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX05201

Powerplus POWX05201 User Manual - German - 11 pages

Powerplus POWX05201 User Manual - Dutch - 11 pages

Powerplus POWX05201 User Manual - French - 11 pages

Powerplus POWX05201 Additional guide - All languages - 4 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX05201 Manual

Product: