676177
8
Zoom out
Zoom in
Previous page
1/12
Next page
POWX0026LI EN
Copyright © 2017 VARO P a g e | 8 www.varo.com
NOTE: If the battery does not fit properly, disconnect it and confirm that the battery pack is the
correct model for this charger as shown on the specification chart.
Do not charge any other battery pack or any battery pack that does not securely fit the charger.
1. Frequently monitor the charger and battery pack while connected.
2. Unplug the charger and disconnect it from the battery pack when finished.
3. Allow the battery pack to cool completely before using it.
4. Store the charger and battery pack indoors, out of reach of children.
NOTE: If battery is hot after continuous use in the tool, allow it to cool down to room
temperature before charging. This will extend the life of your batteries.
8.2 Removal / insertion of battery (Fig. 3)
WARNING: Before making any adjustments ensure the drill is switched off with the direction of
rotation selector (6) in the centre position.
1 Hold the drill with one hand and the battery pack (7) with the other.
2 To install: pull and slide battery pack into battery port, make sure the latch (8) on the
both side of the battery snap into place and battery is secure before begging operation.
3 To remove: use your thumb and fingers, press the battery release latches in and pull
the battery pack off at the same time.
8.3 Switch On/Off (Fig. 4 & 5)
The drill is started and stopped by depressing and releasing the ON/OFF switch trigger (5).
This cordless drill is equipped with an electric brake, when the ON/OFF switch trigger is
released completely the chuck stops immediately.
8.3.1 Rotation (right/left/lock)
Direction of rotation is controlled by the direction of rotation selector (4) located above the
switch trigger.
Right: To select forward rotation, release the on/off switch and push the forward/reverse lever
to the left side of the tool.
Left: To select reverse rotation, push the lever to the right side of the tool.
Lock: When the selector is in the centre position, the switch trigger is locked. (See Fig. 5)
This helps to reduce the possibility of accidental starting when not in use.
8.3.2 Variable speed
This tool has a variable speed switch that delivers higher speed and torque with increased
trigger pressure. The rotational speed is controlled by the amount of switch trigger depression.
8.4 Installing and Removing a Bit and a Drill (Fig. 6)
This drill has a keyless chuck (1) to prevent the bit or drill from loosening.
1 Hold ring A of the drill chuck tight with one hand.
2 Turn upper ring B anticlockwise with the other hand until the drill chuck opening is large
enough to accept the tool.
3 Insert the drill or the screwdriver bit into the drill chuck.
4 Turn ring B clockwise until the tool is clamped tightly.
Remove the tool in the opposite way.
8.5 Adjusting the torque
The torque is adjusted by rotating the torque setting ring (2); the torque is greater when the
torque setting is set on a higher position. The torque is less when the torque setting ring is set
on a low position. Position 1 denotes the lowest and “ ” denote the highest.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0026LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0026LI in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0026LI

Powerplus POWX0026LI User Manual - German - 14 pages

Powerplus POWX0026LI User Manual - Dutch - 13 pages

Powerplus POWX0026LI User Manual - French - 13 pages

Powerplus POWX0026LI Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info