795820
12
Zoom out
Zoom in
Previous page
1/19
Next page
POWDPG7576 EN
Copyright © 2022 VARO P a g e | 12 www.varo.com
13 GENERAL CUTTING INSTRUCTIONS
13.1 Felling
Felling is the term for cutting down a tree. Small trees up to 6-7 inches (15-18cm) in diameter
are usually cut in a single cut. Larger trees require notch cuts. Notch cuts determine the direction
the tree will fall.
Felling a tree:
Warning: a retreat path (A) should be planned and cleared as necessary
before cuts are started. The retreat path should extend back and diagonally
to the rear of the expected line of fall, as illustrated in fig. 10a
Caution: if felling a tree on sloping ground, the chain saw operator should
keep on the uphill side of the terrain, as the tree is likely to roll or slide
downhill after it is felled.
Note: direction of fall (B) is controlled by the notching cut. Before any cuts
are made, consider the location of larger branches and natural lean of the
tree to determine the way the tree will fall.
Warning: do not cut down a tree during high- or changing winds or if there is
a danger to property. Consult a tree professional. Do not cut down a tree if
there is a danger of striking utility wires; notify the utility company before
making any cuts.
General guidelines for felling trees:
Normally felling consists of 2 main cutting operations, notching (C) and making the felling cut
(D). Start making the upper notch cut (C) on the side of the tree facing the felling direction (E).
Be sure you don t make the lower cut too deep into the trunk.
The notch (C) should be deep enough to create a hinge (F) of sufficient width and strength. The
notch should be wide enough to direct the fall of the tree for as long as possible.
WARNING: Never walk in front of a tree that has been notched. Make the
felling cut (D) from the other side of the tree and 1.5 - 2.0 inches (3-5 cm)
above the edge of the notch (C) (Fig. 10b)
Never saw completely through the trunk. Always leave a hinge. The hinge guides the tree. If the
trunk is completely cut through, control over the felling direction is lost.
Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to
move. This will prevent the guide bar from binding in the felling cut if you have misjudged the
falling direction. Make sure no bystanders have entered the range of the falling tree before you
push it over.
Warning: before making the final cut, always recheck the area for bystanders,
animals or obstacles.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWDPG7576 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWDPG7576 in the language / languages: English as an attachment in your email.

The manual is 0.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWDPG7576

Powerplus POWDPG7576 User Manual - German - 21 pages

Powerplus POWDPG7576 User Manual - Dutch - 20 pages

Powerplus POWDPG7576 User Manual - French - 20 pages

Powerplus POWDPG7576 Additional guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info