644863
6
Zoom out
Zoom in
Previous page
1/10
Next page
POWC1060 EN
Copyright © 2017 VARO P a g e | 6 www.varo.com
During the charge process, the current used should correspond to the current of the
battery charger.
Never let moisture, rain or splashed water reaches the charging location.
The ambient temperature must not exceed 40oC. Never expose the device to direct
insulation.
Storage-battery packet, which are defective or damaged or can no longer be recharged,
must be disposed of as hazardous waste. Hand them over at a special collection point.
Never harm our environment. Do not throw unusable storage-battery packet away into the
domestic waste, into fire or into water.
If the electrical cable is damaged, the wire may only be replaced by the supplier or by his
repair workshop. Have repairs carried out only by an authorized specialist only.
Use only storage-battery packet, which have been produced by the original manufacturer.
Always keep the surface of the charger free from dust and dirt.
Insert the battery packet into the charger. Follow the guidelines provided concerning
polarity.
Always remove battery packet before working on the machine
When the battery packet is outside the drill, cover the contacts to avoid short circuits (e.g.
from tools)
Do not throw batteries into water or fire, risk of explosion!
Protect the battery packet from impacts, and don't open it.
Never discharge the battery packet completely and recharge occasionally if not used for a
prolonged period.
7.2 Residual risks
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
The following hazards may arise in connection with the tool’s construction and design:
Damage to lungs if an effective dust mask is not worn.
Damage to hearing if effective hearing protection is not worn.
Health defects resulting from vibration emission if the power tool is being used over longer
period of time or not adequately managed and properly maintained.
WARNING! This machine produces an electromagnetic field during
operation. This field may under some circumstances interfere with active or
passive medical implants. To reduce the risk of serious or fatal injury, we
recommend persons with medical implants to consult their physician and
the medical implant manufacturer before operating this machine.
8 OPERATION
8.1 Charging the battery (fig. 1)
The battery (5) must be charged before first use. Only after several charge and discharge
cycles the battery will attain full capacity.
Remove the battery from the machine. (a)
Connect the battery to the charger. (b)
When the red indicator light starts winking, this means the battery pack is now being
charged. Normally it will take 3-5 hour to fully charge the battery. When the red indicator
light stops winking and the green light starts winking, this means the battery is fully
charged
Avoid short periods of charging. Only charge battery pack when fully empty.
Adaptor, charger and battery pack will be warm when charging. This is normal.
8.2 Positioning and removing a drill or screw bit (fig. 2)
This tool is equipped with a keyless chuck.
Open the chuck by turning the collar.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWC1060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWC1060 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWC1060

Powerplus POWC1060 User Manual - German - 11 pages

Powerplus POWC1060 User Manual - Dutch - 11 pages

Powerplus POWC1060 User Manual - French - 10 pages

Powerplus POWC1060 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info