795364
5
Zoom out
Zoom in
Previous page
1/9
Next page
POWAIR0802 EN
Copyright © 2014 VARO P a g e | 5 www.varo.com
every two hours of use. This must be done directly along the male coupler or the screw
(OIL) provided for the purpose on the side of the tool’s housing.
Automatic lubrication is also possible using the supplied mini oiler that you have to install
between the threaded connector of the tool and the male coupler. Make sure that the oiler
is always filled with suitable oil.
Fig. 1
1. Tool
2. Quick connector
3. Quick coupler
4. Air hose
5. Quick connector
6. Quick coupler
7. Lubricator
8. Regulator (0-8.5 bar)
9. Filter
10. Cut-off valve
11. Air compressor
8 LOADING AND OPERATION
8.1 Drill Bit Installation
Select the drill bit needed for the drilling you wish to perform.
Open up the jaws of the drill by turning the chuck.
When the jaws are open wide enough to insert the drill bit, slide the bit into the drill
chuck as far as possible.
By hand, turn the drill chuck to tighten the jaws and make sure very tight.
8.2 Using the Air Drill
CAUTION: Do not operate the Air Drill before placing the drill bit on the
material.
WARNING: Do not touch the DRILL CHUCK or the drill bit while the Air
Drill is spinning.
Mark the material on the spot for drilling the hole. Make sure your drill bit is the correct
size for the hole you need to make.
Clamp the material in a vise to make sure the material does not move or begins to spin
while drilling.
Wear eye protection to guard against flying wood or metal.
Set the compressor’s pressure regulator to 90 PSI. Do not set the compressor’s outlet
regulator over 90 PSI.
Connect the air drill to the air compressor’s hose. If leaking is detected, disconnect the
air hose and repair before use.
Hold the air drill firmly. Place the drill bit on the spot marked in Step 1.
To begin drilling, press the trigger.
Your air drill has a variable speed for drilling. To vary the speed of the drilling action,
vary the pressure on the trigger.
Drill only as deep as necessary. Do not drill deeper than necessary into walls or other
areas where you cannot identify any possible hazards behind the drilling surface.
When you have drilled the hole, remove the drill bit from the hole while the air drill is
still spinning. This is to prevent the drill getting caught in the hole and causing damage.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWAIR0802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWAIR0802 in the language / languages: English as an attachment in your email.

The manual is 0.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWAIR0802

Powerplus POWAIR0802 User Manual - German - 10 pages

Powerplus POWAIR0802 User Manual - Dutch - 10 pages

Powerplus POWAIR0802 User Manual - French - 10 pages

Powerplus POWAIR0802 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info