795364
4
Zoom out
Zoom in
Previous page
1/9
Next page
POWAIR0802 EN
Copyright © 2014 VARO P a g e | 4 www.varo.com
Maintenance. For your safety, maintenance should be performed regularly by a quali-
fied technician.
Compressed air only. Never use combustible gas as a power source.
Use both hands. The force generated from this tool can cause it to break free of your
grasp, causing serious injury and damage. Always operate this tool with both hands.
Note: Performance of the compressor (if powered by line voltage) may
vary depending on variations in local line voltage. Extension cord usage
may also affect tool performance.
5 AIR SUPPLY
Ensure air valve (or trigger) is in the off position before connecting to the air supply.
You will require an air pressure of 91psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 91psi while operating
the tool. Too high an air pressure and unclean air will shorten the product life due to
excessive wear, and may be dangerous causing damage or personal injury.
Drain the air tank daily. Water in the air line will damage the tool.
Clean air inlet filter weekly.
Line pressure should be increased to compensate for unusually long air hoses (over 8
meters). The minimum hose diameter should be 3/8 I.D. and fittings must have the
same inside dimensions.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make
certain that all connections are secure.
6 LUBRICATION
An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool
life and keeps the tool in sustained operation. The in-line lubricator should be regularly
checked and filled with air tool oil.
Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to
the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator
is properly set when a light stain of oil collects on the paper. Excessive amounts of oil
should be avoided.
In the event that it becomes necessary to store the tool for an extended period of time
(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.
The tool should be run for approximately 30 seconds to ensure oil has been evenly
distributed throughout the tool. The tool should be stored in a clean and dry environment.
It is most important that the tool be properly lubricated by keeping the air line lubricator
filled and correctly adjusted. Without proper lubrication the tool will not work properly
and parts will wear prematurely.
Use the proper lubricant in the air line lubricator. The lubricator should be of low air flow
or changing air flow type, and should be kept filled to the correct level. Use only
recommended lubricants, specially made for pneumatic applications. Substitutes may
harm the rubber compounds in the tools, O-rings and other rubber parts.
7 IMPORTANT!!!
If no filter/ pressure regulator/ lubricator is installed in the compressed air system, then
pneumatic tools must be lubricated with 2 to 6 drops of oil at least once a day or after
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWAIR0802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWAIR0802 in the language / languages: English as an attachment in your email.

The manual is 0.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWAIR0802

Powerplus POWAIR0802 User Manual - German - 10 pages

Powerplus POWAIR0802 User Manual - Dutch - 10 pages

Powerplus POWAIR0802 User Manual - French - 10 pages

Powerplus POWAIR0802 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info