480966
5
Zoom out
Zoom in
Previous page
1/8
Next page
POW30540 EN
Copyright © 2013 VARO Page | 5 www.varo.com
Due to their working principle, SDS-Plus drilling tools move freely. This results in radial run-out
at no-load. However, this has no effect on the accuracy of the drill hole, as the drill bit centres
itself during drilling.
The SDS-Plus tool holder can also accommodate different drill-bit types with hexagon shank.
Use only bit with SDS-Plus. Other bits can be used with a keyless chuck with SDS-Plus.
8 OPERATION
8.1 Forward/reverse selector (right/left rotation selector) Fig. 2
The drill has a forward/reverse selector located above the switch trigger
§ To make the drill rotate clockwise for drilling or driving screws, push the forward /reverse
switch to the left.
§ To make the drill rotate counter clockwise for removing screws, push the forward /reverse
switch to the right.
Never change the position of the forward /reverse switch while chuck is
turning.
The trigger switch will NOT function with the forward /reverse switch in the
middle position
8.2 Trigger switch lock-on button
The trigger switch lock-on feature allows the trigger switch to be locked in the ON position at
full speed when continuous operation for extended periods of time is required (Fig. 2).
§ To lock the trigger switch in the ON position, pull the trigger switch back fully to operate
the drill at full speed.
§ While holding the trigger fully back, push the lock-on button (3) into the drill handle. The
drill will continue to run.
§ To release the lock-on button, pull the trigger switch back and then release the trigger.
8.3 Drill / hammer control
The drill /hammer control changes the drilling mode between conventional drilling and hammer
for drilling concrete (Fig. 3).
To change from drilling mode to hammer mode, push the end of the drill /hammer control knob
inward and rotate the knob 180°to the hammer mode. Reverse the procedure to change from
hammer mode to drilling mode.
When the drill /hammer control knob reaches the desired position, release
the end of the drill /hammer control knob and move the knob back and forth
slightly. You will hear the knob lock into position.
Change the operating mode only when the machine is switched off!
Otherwise, the machine can be damaged.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW30540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW30540 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW30540

Powerplus POW30540 User Manual - German - 10 pages

Powerplus POW30540 User Manual - Dutch - 9 pages

Powerplus POW30540 User Manual - French - 9 pages

Powerplus POW30540 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info