391294
8
Zoom out
Zoom in
Previous page
1/12
Next page
POWXQ5104 EN
Copyright © 2012 VARO NV P a g e | 8 www.varo.com
Move the spring, holding the cole brush aside, remove the wire connector and pull out the cole,
install the new one (don’t forget to reposition the spring) and close the brush caps again.
Let the machine run freely without load for a while, allowing the coles to fit right (sparking may
occur, but is not harmful and will disappear after a while)
If you are not confident to perform this by yourselves, ask a qualified person to do it for you.
7.4 Mounting the side handle (Fig 5)
The side handle can be used for both left-hand and right-hand control.
Fasten the side handle for left-hand operation on the right-hand side of the machine.
Fasten the side handle for right-hand operation on the left-hand side of the machine.
Fasten the side handle for upright working at the top of the machine.
Make sure that the side handle is fastened properly and cannot loosen
unexpectedly.
8 OPERATION
8.1 Pay special attention when starting the machine
Clamp the workpiece and make sure that the workpiece cannot slide from under the
machine during the cutting activities.
When working with the machine, always hold it firmly with both hands and provide for a
secure stand.
Always direct the cable to the rear away from the machine to avoid cutting the electric
cable.
Insert the mains plug only when the machine is switched off.
Apply the machine to the workpiece only when switched on and when it has reached full
speed.
When cutting into walls! Make sure to avoid hidden electrical wiring (electric shock!) or
pipes (water, gas...).
Make sure the grinding/cutting disc is not contacting the work piece before the switch is
turned on.
Keep hands away from rotating parts.
Never use the machine for grinding magnesium workpieces.
8.2 Switching On (Fig 6)
To switch on:
POWXQ5104: press the “lock on” safety knob at the left side of the handle, keep it pressed
then squeeze the on/Off switch.
Allow the disc to reach full speed before you touch the workpiece.
8.3 Switching Off (Fig 7)
To switch off:
POWXQ5104 : simply release the ON/OFF switch, the machine will be switched OFF.
The disc will gradually slow down and eventually stop after a few seconds.
Do not put the machine down when the disc is still turning.
Never unplug a running machine, always switch off first before pulling out the
plug!
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow xq5104 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow xq5104 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow xq5104

Powerplus pow xq5104 User Manual - German - 13 pages

Powerplus pow xq5104 User Manual - Dutch - 13 pages

Powerplus pow xq5104 User Manual - French - 13 pages

Powerplus pow xq5104 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info