383782
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWXQ5302 EN
Copyright © 2015 VARO P a g i n a | 7 www.varo.com
Soft wood: high cutting speed.
When processing metals you should use suitable lubricants/coolants to protect the saw blade
just a little oil for steel, and spirit or petroleum for aluminium, as required. For plastic material
water is normally sufficient as the coolant/lubricant.
8.2 Changing the saw blade (fig 2)
Insert the small hex key through the transparent guard (7) at the side of the tool and
loosen the hex screw.
Slide the blade into the locating groove with teeth pointing forward. Make sure that the
back edge of the blade fits into the guide wheel (8).
Tighten the screw.
8.3 Angle cutting adjustment( fig3)
Loosen the hex head screw located on the underside of the tool using the inner hexagon
spanner provided.
Move the base (12) forward and tilt it until the desired angle is obtained The angle can be
between 0°and 45° (left and right).
Tighten the hex screw.
For accurate cut it is necessary to make a trial cut, measure the work and reset the angle
until the correct setting is achieved.
8.4 Edge guide( fig 4)
With the edge guide you can saw parallel to an edge.
Insert the edge guide (14) into the base (12).
Set the edge guide.
Tighten the screw (13) of edge guide.
8.5 Using the laser (6)
Do not stare directly at the laser (6) beam. Never aim the beam at anyperson
or an object other than the workpiece.
Always ensure the laser beam is aimed at a sturdy work piece without
reflective surfaces i.e. Wood or rough coated surfaces are acceptable.
Bright shiny reflective sheet steel or the like is not suitbale for laser use as
the reflective surface could direct the beam back at the operator.
The laser beam projects a red cutting line on the work piece.
Switch the laser (6) on by means of the on/off switch (5).
Place the machine on the work piece with the saw marking above the start of the cutting
line.
Check that the laser line aligns with the cutting line as marked on the work piece.
Switch on the machine.
After use, switch off the laser.
8.6 Use of pendulum (10)
This jig saw is equipped with four cutting actions, one straight and three orbital. Orbital action
has a more aggressive blade motion and is designed for cutting in soft materials like wood or
plastic. Orbital action provides faster cut, but with a rougher cut across the material. In orbital
action, the blade moves forward during the cutting stroke in addition to the up and down
motion.
Note: Metal or hardwoods should never be cut in orbital action.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow xq 5302 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow xq 5302 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow xq 5302

Powerplus pow xq 5302 User Manual - German - 11 pages

Powerplus pow xq 5302 User Manual - Dutch - 11 pages

Powerplus pow xq 5302 User Manual - Dutch - 10 pages

Powerplus pow xq 5302 User Manual - French - 12 pages

Powerplus pow xq 5302 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info