383782
6
Zoom out
Zoom in
Previous page
1/11
Next page
POWXQ5302 EN
Copyright © 2015 VARO P a g i n a | 6 www.varo.com
Do not leave power tools running unattended. Always switch off and do not put down or
leave until it has stopped completely.
Long hair must be covered. Do not work in loose fitting clothing.
Be careful when working on walls. Damage to power supply lines, gas or water pipes can
lead to dangerous situations. Use appropriate detectors to establish whether there are
concealed wires or pipes in the working area.
Always check that the mains voltage corresponds to the voltage on the device's rating
plate.
Secure the work piece. The work piece is only secure if it is held by work-holding devices
or in a vice.
Use of extension cables. Only use extension cables which are designed for the machine's
power. The minimum conductor cross section must be 1.5 mm². When using cable reels
the cable must always be completely unrolled.
Always remove the mains plug before replacing saw blades.
Caution: saw blades can get very hot.
Saw blades (9) must be kept sharp and in good condition. Replace partially fractured and
broken saw blades immediately.
Work calmly and evenly with the jig saw. You will thus avoid accidents and the saw blades
and the jig saw will last longer.
7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Warning! The laser beam potentially causes eye damage. Do not look or
stare into the laser beam.
During use, do not point the laser beam at people, directly or indirectly through reflecting
surfaces.
This laser complies with class 2 according to EN 60825-1. The unit includes no servicing
components. Do not open the housing for any reason. If the unit is damaged, have the
damage repaired by an authorized repair agent.
Laser viewing glasses are not protective glasses against laser radiation.
8 OPERATING INSTRUCTIONS
8.1 Starting up
8.1.1 Switching on and off
Connect the plug to the power supply.
To start the tool, depress the switch lock off (2) button and pull the trigger(3) to turn on
the tool.
Release the trigger to turn the tool off.
8.1.2 Adjusting the cutting speed
Using the speed regulator (4) on the top, you can pre-set any speed. Turn the speed regulator
(4) to a higher number for a higher speed and turn it to a lower number for a lower speed. The
ideal cutting rate depends on the specific material and working conditions.
The general standards for setting the cutting speed for power tools apply here.
Steel: slowest cutting speed
Aluminium, plastic, hardwood: medium cutting speed.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow xq 5302 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow xq 5302 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow xq 5302

Powerplus pow xq 5302 User Manual - German - 11 pages

Powerplus pow xq 5302 User Manual - Dutch - 11 pages

Powerplus pow xq 5302 User Manual - Dutch - 10 pages

Powerplus pow xq 5302 User Manual - French - 12 pages

Powerplus pow xq 5302 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info