389044
9
Zoom out
Zoom in
Previous page
1/12
Next page
POW X0153, 0155 & 0157
EN
Copyright © 2011 VARO
P a g e | 9
www.varo.com
POW X0157 only:
For hammer drilling
* Drilling hard smooth surfaces
When drilling hard smooth surfaces use a centre punch to mark desired hole location. This will
prevent the drill bit from slipping off centre as the hole is started. However, the low speed
feature allows starting holes without centre punching if desired. To accomplish this, simply
operate the drill at a low speed until the hole is started. The material to be drilled should be
secured in a vise or with clamps to keep it from turning as the drill bit rotates. Hold tool firmly
and place the bit at the point to be drilled. Move the drill bit into the work piece applying only
enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole.
WARNING:
Be prepared for binding or bit breakthrough. When these situations occur, drill has a tendency
to grab and kick opposite to the direction of rotation and could cause loss of control when
breaking through material. If not prepared, this loss of control can result in possible serious
injury. hen drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will
prolong the life of the bit and increase the drilling action. If the bit jams in work piece or the drill
stalls, release switch trigger immediately. Remove the bit from the work piece and determine
the reason for jamming.
9 CLEANING AND MAINTENANCE
9.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
9.2 Maintenance
Our machines have been designed to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon proper machine care and
regular cleaning.
10 CHUCK REMOVAL/REPLACEMENT)
10.1 Chuck removal:
Lock the switch trigger by placing the direction of rotation selector in centre position.
Open the chuck jaws and remove the hex key. Remove the chuck screw, turning it in a
clockwise direction. Note: the screw has left hand threads.
Insert the hex key in the chuck and tighten chuck jaws securely. Tap sharply with a mallet in
a counter clockwise direction. This will loosen the chuck on the spindle. It can now be
unscrewed by hand.
10.2 (Re)tighten a (loose) chuck
The chuck may become loose on spindle and develop a wobble. Periodically check chuck
screw for tightness.
To tighten, follow these steps:
Lock the switch trigger by placing the direction of rotation selector in centre position.
Open the chuck jaws.
Insert the hex key into the chuck and tighten chuck jaws securely. Tap the hex key sharply
with a mallet in a clockwise direction. This will tighten the chuck on the spindle.
Open the chuck jaws and remove the hex key.
Tighten the chuck screw.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow x 0157 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow x 0157 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow x 0157

Powerplus pow x 0157 User Manual - German - 13 pages

Powerplus pow x 0157 User Manual - Dutch - 13 pages

Powerplus pow x 0157 User Manual - French - 13 pages

Powerplus pow x 0157 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info