613976

Powerpeak Slim Line FET8315P manueel Manual

26
Zoom out
Zoom in
Previous page
1/72
Next page
26
Longwoods Ltd._04_2013
TIME
Press the ENTER-key until TIME function appears on the display. Next, press the UP- or DOWN-key
to set the time. Time is adjustable from 1:00 – 99:00 minutes. The computer counts down from the
set value to 00:00. An audio signal sounds once the set value has been reached. If you do not preset
any time, the computer will display the current training time from 00:00 – 99:59 minutes.
SPEED
The computer displays the current speed from 0.0 – 99.9 km per hour.
RPM
The computer displays the current revolutions per minute from 15 – 999 revolutions.
DISTANCE
Press the ENTER-key until DIST. (distance) function appears on the display. Next, press the UP- or
DOWN-key to set the distance. The distance can be set from 1.0 – 999.0 km. The computer counts
down from the set value to ‘0.0’. An audio signal will sound once the set value has been reached.
If you do not preset any distance, the computer will display the current covered distance from 0.1 –
999.9 km.
CALORIES
Press the ENTER-key until CAL. (calories) function appears on the display. Next, press the UP- or
DOWN-key to set the calories to be burned. The number of calories to be burned can be set from 1.0
– 999.0 calories. The computer counts down starting from the set value to ‘0.0’. An audio signal will
sound once the set value has been reached. If you do not preset the number of calories to burn, the
computer will display the current burned calories from 0.1 – 999.0 calories.
T.H.R.
Press the ENTER-key until T.H.R. function appears on the display. Next, press the UP- or DOWN-key
to set the number of heartbeats per minute. The number of heartbeats per minute can be set from
60-220 pulses. Place your palms on the hand pulse sensors on the handlebar. The display shows
you the current number of beats per minute. An audio signal will sound once the set value has been
reached.
Attention: if during 15-20 seconds no signal is being transmitted from the hand sensors, a ‘P’ will
appear on the display. This means that the computer is in energy saving mode. Press any key to
resume the T.H.R. measurement.
RECOVERY
Press on RECOVERY-key if you wish to measure your condition after the training. Place your palms
for 1 minute on the hand pulse sensors on the handlebar. The display shows the condition in a figure
ranging from 1.0 to 6.0, where 1.0 indicates a good condition and 6.0 a bad condition.
IMPORTANT ADVICE FOR TRAINING
• Before you start the training, consult your doctor. Ask what kind of training is suitable for you.
Wrong or excessive training can cause health defects.
• Avoid over exercising. Do not train if you are tired or feeling faint. If you are not used to physical
activity, start the training slowly at the beginning.
• Stop exercising immediately if you feel pain or any other troubles.
• Pay attention to your breathing during training.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerpeak Slim Line FET8315P manueel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerpeak Slim Line FET8315P manueel in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info