614065

Powerpeak Comfort line FTM6715 Manual

45
Zoom out
Zoom in
Previous page
1/66
Next page
45
Cycle switch order is: manual, time, distance, calories.
BELT ADJUSTMENT
You may need to adjust the running belt during the first few weeks of use. All running belts are
properly set at the factory. It may stretch or be off centre after use. Stretching is normal during the
break-in period.
Adjusting the belt tension
If the running belt feels as though it is slipping or hesitating when you place your foot on it during a
run, the tension on the running belt may have to be increased. To increase the running belt tension:
5. Start the treadmill without anyone on the running belt, press SPEED+ button until speed reaches
between 5 and 6 km/h.
6. Place a wrench on the left adjustment screw. Turn the wrench clockwise 1/4 turn to draw the
rear roller and increase the belt tension.
7. Repeat step 2 for the right adjustment screw. You must be sure to turn both bolts the same
number of turns, so the rear roller will remain square relative to the frame.
8. Repeat step 2 and step 3 until the slipping is eliminated.
Note: be careful not to tighten the running belt tension too much as you can create excessive
pressure on the front and rear roller bearings. An excessively tightened running belt may damage
the roller bearings resulting in bearing noise from the front and rear rollers.
Centering the running belt
When you run, you may place more pressure on the belt with one foot than with another. The
severity of this deflection depends on the amount of force that one foot exerts in relation to the
other. This deflection can cause the belt to move off-centre. This deflection is normal and the
running belt will centre when nobody is on the running belt.
If the running belt remains consistently off-centre, you will need to centre the running belt manually:
5. Place the device on a level surface.
6. Start the treadmill without anyone on the running belt, press SPEED+ button until speed reaches
5,6 km/h.
7. Observe whether the running belt is toward the right or left side of the deck.
a. If toward the left side of the deck:
Turn the left adjustment screw clockwise 1/2 turn, and the right adjustment bolt
counter clockwise 1/2 turn.
b. If toward the right side of the deck:
Turn the right adjustment screw clockwise 1/2 turn, and the left adjustment bolt
counter clockwise 1/2 turn.
PI
PI
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerpeak Comfort line FTM6715 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerpeak Comfort line FTM6715 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info