706369
10
Zoom out
Zoom in
Previous page
1/44
Next page
GB
IE
NI
 7
PLBS 2 A1
Place the outer tab of the cover back on the
centring rib of the cover.
Swing the cover back until the release buttons
click audibly into place on both sides.
Ensure that the cover is firmly in place on the
drill dust collector. This is the only way to pre-
vent dust escaping.
Appliance suction function
After you have aligned the laser or put the drill
dust collector/drill against the wall, switch on
the vacuum pump at the switch .
Push the appliance briefly firmly against the
wall. After a short time, the appliance will be
firmly sucked against the wall.
Ensure that the seal
of the appliance is fully
against the wall.
Check that the appliance stays in place by
trying gently to pull it off or slide it across the
surface.
Leave the vacuum pump switched on the whole
time you are working with the line laser and/or
the drill dust collector. Otherwise, the appliance
will not be able to maintain a sufficient vacuum
and the appliance could come off the wall.
Do not use the appliance for overhead work.
If the appliance does not remain on the wall,
it may be because the surface structure of the
wall is simply too rough, and the appliance is
unable to generate a sufficient vacuum. In this
case, you will need a second person to hold the
appliance in place.
Ensure that the seal
is not damaged or cut
by rough surfaces, edges or corners.
Detaching the appliance
First, finish your work with the line laser and/
or the drill and then remove the drill from the
appliance.
Hold the appliance firmly in place to prevent it
from falling down.
Switch off the vacuum pump at the switch
and press the vacuum button .
Remove the appliance from the surface.
Use the protective cover
to protect the appli-
ance and the seals .
Troubleshooting
The laser is not working
Battery is dead > replace battery.
Appliance does not grip onto the surface
Battery is dead or too weak > replace battery.
Seal is damaged > Hold the appliance by
hand.
Wall structure is too rough > Hold the appli-
ance by hand.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerfix Profi PLBS 2 A1 - IAN 277698 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerfix Profi PLBS 2 A1 - IAN 277698 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info