706369

Powerfix Profi PLBS 2 A1 - IAN 277698 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
■ 6 
│
 GB
│
IE
│
NI
PLBS 2 A1
Getting started
■ After inserting the batteries, the appliance is
ready for use.
■ Remove the protective cover/wall bracket
from the appliance.
■ Fully grip the appliance with one or, ideally,
both hands. The appliance is suitable for either
hand.
Operation
CAUTION!
► Use the appliance only for its intended use.
► Check the appliance for damage before use.
Do not use the appliance if its operational
safety cannot be guaranteed.
Switching the line laser on and off
♦ To switch the line laser on and off, press the
ON/OFF switch .
■ To make the levels
easier to read, these
are illuminated.
♦ Switch the laser off again by pressing the
ON/OFF switch
.
Aligning the line laser
♦ Align the appliance using the horizontal and
vertical levels
by changing the tilt angle of
the appliance. Centre the air bubble in one of
the levels between the two marking lines.
♦ For diagonal alignment of the laser, mark two
points in the desired alignment and line up the
laser with these markings.
♦ Switch on the vacuum pump (see section
Appliance suction function).
♦ To use the line laser
without the suction func-
tion, you can release it from the mount by pulling
it in a horizontal direction.
♦ Replace the line laser on the guide and push it
in the direction of the battery compartment
until it clicks audibly into place.
Using the drill dust collector
♦ Mark the spot on the wall where you want to
drill the holes.
♦ Push the loaded drill through the opening on
the protective plate
until it comes out of the
other side of the seal .
♦ Put the tip of the drill bit onto the marking.
♦ Hold the drill vertically to the wall.
♦ Push the drill dust collector
up against the
wall so that the seals lie up against the
wall.
NOTE
► To ensure that the drill dust collector
collects
the dusts optimally, it should always be
aligned vertically.
♦ Switch on the vacuum pump (see section
Appliance suction function).
♦ Hold the drill firmly in both hands and follow the
manufacturer's operating and safety instructions.
♦ Use only suitable drills up to a max. 10 mm in
diameter.
♦ Wear your personal protective equipment
(safety goggles)!
♦ Pull the drill out of the drill dust collector
before you switch off the vacuum pump.
Emptying the drill dust collector
♦ Point the drill dust collector downwards.
Press the release buttons together on both
sides between your thumb and index finger and
swing the cover of the drill dust collector
upwards.
♦ Empty the drill dust collector
.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerfix Profi PLBS 2 A1 - IAN 277698 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerfix Profi PLBS 2 A1 - IAN 277698 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info