754135

Powerfix PDM 300B1 - IAN 285130 Manual

9
Zoom out
Zoom in
Previous page
1/64
Next page
POWERFIX PDM 300 B1
English - 7
If smoke is produced, or there are any unusual sounds or smells, stop measuring immediately. In
these cases, the multimeter should not be used until it has been inspected by authorised service
personnel. Never inhale smoke from a potential device fire. If you have inhaled smoke, however,
consult a doctor. The inhalation of smoke can be harmful.
The test probes may be handled only behind the finger protection as otherwise there is a risk of
an electric shock when measuring!
If the multimeter or the test probes are damaged (including test lead), they must not be used. There
is a risk of an electric shock!
Pay particular attention to your safety when dealing with AC voltages over 30V or DC voltages
over 60V. There is a risk of an electric shock!
Never operate the multimeter when the housing is open. There is a risk of an electric shock!
Ensure that you do not touch the test probes and the jacks to be measured during a measurement
in order to avoid an electric shock.
Do not use the multimeter in wet or damp environments. Also ensure that your hands and shoes
are dry as there is a risk of an electric shock otherwise!
Do not use the multimeter in the vicinity of explosive gases or vapours or in a dusty environment.
It poses a risk of explosion!
Ensure that no fire sources (e.g. burning candles) are placed on or near the multimeter. It poses a
fire hazard!
Do not exceed the maximum specified input values for the individual measuring ranges. Otherwise,
the multimeter could be damaged.
Do not exceed the specified overvoltage category CAT III. Otherwise, the multimeter could be
damaged.
CAT III: Measurements within the building installation (e.g. distributors, wiring, sockets and
switches). This category also includes the following two categories: CAT II: Measurements on
electrical and electronic devices that are supplied with a voltage via a mains plug.
CAT I: Measurements on circuits that have no direct connection to the mains power supply (battery
operated, motor vehicle electrics, etc.).
The multimeter must be disconnected from the test object before changing the measuring range as
the multimeter could be damaged otherwise.
When working with the test probes, first connect the black test lead to the COM jack before you
connect the red test lead. When disconnecting the test probes, first remove the red test probe.
Never connect a voltage source to the test probes if the areas continuity test, resistance
measurement, diode test, function generator or current measurement are selected. Otherwise, the
multimeter could be damaged.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerfix PDM 300B1 - IAN 285130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerfix PDM 300B1 - IAN 285130 in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerfix PDM 300B1 - IAN 285130

Powerfix PDM 300B1 - IAN 285130 User Manual - French, Portuguese, Spanish - 142 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info