628495
102
Zoom out
Zoom in
Previous page
1/105
Next page
Example Description Status Message
F01SSEN1
Enable screen saver.
F01SSEN1
F01SSEN0
Disable screen saver.
F01SSEN0
F01SSEN2
Toggle screen saver enabled state.
F01SSENx , where x is 0 or 1 depending on the current
enabled state of the scrren saver.
F01SSEN?
Query screen saver enabled state.
F01SSENx , where x is 0 or 1 depending on the current
enabled state of the scrren saver.
8.132. SSSTART -- Set Idle Time Required for Screen Saver to
Start
This command sets or queries the amount of time (in milliseconds) that the front panel buttons must be idle
before the screen saver starts.
This command is an integer command. See
Section 6.2 for more information on this type of command. The
minimum and maximum values for this command are 500 and 600000, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01SSSTART2000
Set screen saver start time to 2
seconds (2000 ms).
F01SSSTART2000
F01SSSTART>500
Increase screen saver start time by
0.5 seconds (500 ms).
F01SSSTARTx , where x is the new value of the
screen saver start time. If this command was issued
after the example above, then the status message
would be F01SSSTART2500 .
F01SSSTART?
Query screen saver start time.
F01SSSTARTx , where x is the new value of the
screen saver start time. If this command was issued
after the example above, then the status message
would be F01SSSTART2500 .
8.133. SSTEXT -- Set Text to be Displayed by Screen Saver
This command sets or queries the text messages displayed by the screen saver. The arguments of this command
are the screen number, the line number, and the text to be displayed. The screen number must be between 0
and 3. It indicates which message screen we are trying to set or query. Each message screen consists of two
lines of text that can be up to 16 characters long. The second number indicates which line of the message we
are tring to set or query. The line number must be 0 or 1 corresponding to the first and second line, respectively.
Finally, the text argument is the actual text that will be displayed on the LCD. If the text is '?', then a query will
be performed. If the text empty, then the message will be cleared. If both message lines are cleared for a given
screen, then that screen will not be displayed by the screen saver. If all screens have been cleared, then the
screen saver will never start (although it is easier just to use the
SSEN command for this).
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info