628495

Polycom Vortex EF2280 Manual

83
Zoom out
Zoom in
Previous page
1/105
Next page
F01NC*2
Toggle NC state on all microphone input
channels (1-8) .
F01NC*abcdefgh , where the letters (a, b, etc.) are each
0 or 1 depending on the current state of NC for each of
the corresponding input.
F01NC*?
Query NC state on all microphone input
channels (1-8) .
F01NC*abcdefgh , where the letters (a, b, etc.) are each
0 or 1 depending on the current state of NC for each of
the corresponding input.
8.99. NCL -- Set Noise Cancellation Attenuation
This command sets or queries the attenuation level of the Noise Cancellation algorithm on input channels 1-8 .
For example, if NCL is set to 10, then the Noise Cancellation for that channel will cancel 10 dB of noise. Higher
numbers mean more cancellation will be applied, but may result in slight artifacts depending on the
characteristics of the noise. Typical settings are 10 dB for normal cancellation and 6 dB for light cancellation.
This command is a channel integer command. See
Section 6.3 and Section 6.2 for more information on this type
of command. The minimum and maximum values for this command are 0 and 20, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01NCL13
Set NC attenuation level on input
channel 1 to 3 dB.
F01NCL13
F01NCL1?
Query the NC attenuation level on
input channel 1 .
F01NCL1x , where x is a number between 0 and 20,
depending on the current setting of the NC attenuation
level on input channel 1 .
F01NCL*6
Set NC attenuation level on all
microphone input channels (1-8)
to 6 dB.
F01NCL*èèèèèèèè
F01NCL*ääääìììì
Set NC attenuation level on input
channels 1-4 to 0 dB and NC
attenuation level on input
channels 5-8 to 9 dB.
F01NCL*ääääìììì
F01NCL*?
Query NC attenuation level on all
microphone input channels (1-8) .
F01NCL*abcdefgh, where a-h are each between ä
and ÿ, depending on the current setting of the NC
attenuation level for each of the eight input channels.
8.100. NVINIT -- Reinitialize Non-Volatile Memory
This command reinitializes (or formats) all non-volatile memory settings. This will effectively erase settings for
global settings, user presets, macros, labels, and logic I/O configurations. This will basically reset the unit to a
"fresh-out-of-the-box" state.
When this command is issued, it writes to non-volatile memory in order to format the contents back to the
factory default state. The writing process results in a short delay. After the non-volatile memory has been
reformatted, the Vortex will perform a software reset, which is equivalent to a power cycle.
Example Description Status Message
… 83 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info