628495
68
Zoom out
Zoom in
Previous page
1/105
Next page
Logic output 10 will be deactivated if:
(input 1, input 2, input A, and input B are unmuted) AND
(input C OR input D is muted)
An error condition of ERROR#074 will be generated if the assigned command is invalid.
This command is saved to global non-volatile memory and is not part of a preset. Its value is saved each time it
is changed. It will retain its value after power-down. Since this command writes to non-volatile memory, there
will be a delay before an acknowledgment is returned.
Example Description Status Message
F01LOA10,MUTEI*1100++--....
Configure the conditions for
activation of logic output 10 as
described in the example above.
F01LOA10,MUTEI*1100++--....
F01LOA7,
Delete conditions for activation of
logic output 7.
F01LOA7,
8.75. LOD -- Define Behavior for Logic Output Deactivated Status
This command is used to define the conditions under which a given logic output pin goes into the deactive state.
The syntax and behavior of this command is identical to that of the
LOA command. Please refer to the
description of the
LOA command for more information, including examples.
This command is saved to global non-volatile memory and is not part of a preset. Its value is saved each time it
is changed. It will retain its value after power-down. Since this command writes to non-volatile memory, there
will be a delay before an acknowledgment is returned.
8.76. LOEN -- Enable Automatic Logic Output Status Messages
This command controls whether or not logic output status messages are sent automatically. If LOEN is enabled,
then a logic output query (LO*?) is performed any time any of the states change on the logic output pins. For
example, if all logic outputs are currently in the low state ('0') and LOEN is enabled, then if logic output 12
changes state to '1', the following status message will be generated:
F01LO*00000000000100000000
A status message is only generated if there is a state change. This helps keep data traffic to a minimum.
This command is a boolean command. See
Section 6.1 for more information on this type of command.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01LOEN1
Enable automatic logic output status messages.
F01LOEN1
F01LOEN0
Disable automatic logic output status messages.
F01LOEN0
F01LOEN2
Toggle automatic logic output status messages.
F01LOENx , where x is 0 or 1 depending on the
current setting of LOEN.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info