628495

Polycom Vortex EF2280 Manual

65
Zoom out
Zoom in
Previous page
1/105
Next page
Using this command is more efficient than deleting one command or pin at a time since this command deletes
them all at once and requires fewer writes to non-volatile memory.
This command is saved to global non-volatile memory and is not part of a preset. Its value is saved each time it
is changed. It will retain its value after power-down. Since this command writes to non-volatile memory, there
will be a delay before an acknowledgment is returned.
Example Description Status Message
F01LIK5
Delete all the commands associated with logic input pin 5. This one command is
equivalent to executing the commands 'F01LIA5, ', 'F01LID5, ', and
'F01LIH5, ' except that this command is more efficient.
F01LIK5
F01LIK*
Delete all the commands associated with all logic input pins. This one command is
equivalent to executing the commands 'F01LIA1, 'F01LID1, ', and 'F01LIH1, '
for each logic input, except that this command is much more efficient.
F01LIK*
8.70. LIM -- Mask Logic Input Pins
This command is used to mask (i.e., disable) logic input pins. The mask consists of 24 fields (one for each logic
input) that can each be set to 0 or 1. If the mask bit for a given logic input is set to 1, then the logic input pin
works normally. If the mask bit for a given logic input is set to 0, then the logic input is disabled. When a logic
input is disabled, any commands assigned to the logic pin via
LIA, LID, and LIH will not be executed.
If a logic pin is disabled and then re-enabled at some later time and the logic input has changed state from when
it was disabled, the command associated with the state change will be executed. For example, if a logic input pin
is high when it is disabled, and it is low when it is re-enabled, the command defined via
LID (or LIA if the
polarity is changed via
LIP) will be executed. However, if the pin changes state multiple times while it is
disabled, multiple commands will not be executed; only the difference in state when the logic input is re-enabled
is considered.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01LIM100101101111011111111111
Mask (disable)
logic inputs 2, 3,
5, 8, and 13.
F01LIM100101101111011111111111
F01LIM?
Query current
logic input
mask.
F01LIMabcdefghijklmnopqrstuvwx where a-x
are each 0 or 1 depending on the current state of
the logic input mask.
8.71. LIN -- Assign Command to Logic Input Group
This command assigns a command to be executed when a group of logic input pins is in a certain configuration.
Logic groups are defined via the
LIG command.
As an example, assume that the command F01LIG2,000001111100000000000000 has been sent to the
device. This command configures logic input pins 6-10 to be part of logic group 2. Now, we send the command
F01LIN2,10,MACROX25 . This command configures logic input group 2 to execute the command MACROX25
when logic inputs 7 and 9 are active ('1') and logic inputs 6, 8, and 10 are inactive ('0'). The first number in the
… 65 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info