628495
49
Zoom out
Zoom in
Previous page
1/105
Next page
This command is a channel integer command. See Section 6.3 and Section 6.2 for more information on this type
of command. The minimum and maximum values for this command are -100 and 20, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01FADERI210
Set fader gain on input
2 to 10 dB.
F01FADERI210
F01FADERI2?
Query the fader gain on
input 2 .
F01FADERI2x , where x is a number between 0 and
20 , depending on the current setting of the fader gain
on input channel 2 .
F01FADERI*6
Set fader gain on all
inputs (1-8, A-D) to 6
dB.
F01FADERI*èèèèèèèèèèèè
F01FADERI*ääääääääìììì
Set fader gain on input
channels 1-8 to 0 dB
and gain on input
channels A-D to 9 dB.
F01FADERI*ääääääääìììì
F01FADERI*?
Query fader gain on all
inputs (1-8, A-D) .
F01FADERI*abcdefghijkl, where a-l are each
between ä and ÿ, depending on the current setting of
the fader gains for each of the twelve input channels.
8.45. FLOW -- Set Flow Control Mode for RS-232 Port
This command sets the flow control mode for the rear panel RS-232 port. The valid settings are:
Command Value Description
0 No flow control.
1 Hardware flow control.
2 Auto-detect hardware flow control or no flow control.
We recommend using hardware flow control whenever possible, especially when using higher baud rates.
This command is saved to global non-volatile memory and is not part of a preset. Its value is saved each time it
is changed. It will retain its value after power-down. Since this command writes to non-volatile memory, there
will be a delay before an acknowledgment is returned.
Example Description Status Message
F01FLOW1
Set rear panel RS-232 port to use hardware flow
control.
F01FLOW1
F01FLOW?
Query flow control setting of rear panel RS-232 port.
F01FLOWx , where x is 0, 1, or 2 depending
on the current flow control setting.
8.46. FPLOCK -- Lock/Unlock Front Panel
This command controls the front panel lock feature. When FPLOCK is enabled, the user may not make any
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info