Manual Polti MONDIAL VAP 2000 (page 8 of 12) (English)

648834

Zoom out

Zoom in

1/12

ENGLISH

’’

All POLTI machines are equipped with the unique Polti patented safety cap, which prevents

opening of the generator tank as long as there is any pressure remaining inside the tank.

This is an important and indispensable safety device, and it is necessary to follow certain

procedures when re-filling the tank.

According to model, ‘water out’ is indicated by a warning light (J), or by an audible alarm

signal from the machine, or on more basic models by the exhaustion of the steam output.

Whenever you have used up all the water in the tank, follow the following procedures:

1c. Switch off the machine at the generator on/off switch (B)

2c. Press the steam request lever (3) on the hand gun (2) or, if using the iron, the steam

request button (R) on the iron (Q) so as to fully exhaust the steam supply from the tank.

3c. Disconnect the power supply cable (F) from the mains.

4c. Unscrew anti-clockwise the patented safety cap (A)

5c. Wait 3 to 4 minutes to allow the generator tank to cool down.

6c. When cool proceed to carefully refill the tank as described in paragraph 1 of the sec-

tion “Preparation for Use” in the instructions. If refilling the generator when not com-

pletely cooled, we recommend that you carefully pour only very small quantities of

water at each pouring into the tank, so as to avoid spitting from the tank and cover

exposed skin whilst filling.

(normally sold separately)

1d. Connect the connector block at the end of the iron hose (4) to the generator as shown

in point 2A of the section “Instruction for Use”.

2d. For all steam ironing, position the temperature indicator dial (F) to the position

“COTONE - LINO”. For dry ironing set the temperature control dial according to the

fabric to be ironed as indicated on the dial.

3d. Wait three to four minutes for the indicator (R) to go out indicating that the sole plate

of the iron has reached the correct temperature.

4d. Press the steam request button on the iron (R) to allow the steam to exit. Releasing

this button stops the steam flow. At first you may find that the steam contains some

water globules and we recommend that the first jet of steam is therefore played onto

an old cloth, and is not directed onto the garment to be ironed.

For dry ironing do not press the steam request button (R).

5d. In order to have a continuous steam jet, move the button (U) forwards. Steam will keep

on coming out, even if you release the button. To interrupt the outlet, move the but-

ton (U) backwards.

6d. The iron can also be used in a vertical position e.g. for removing creases from cur-

tain, clothing etc.

IMPORTANT

• Do not leave the iron unattended whilst connected to the mains.

• Iron only on heat resistant surfaces on and on surfaces that allow the steam to escape

e.g. mesh ironing boards.

Is it possible for the safety cap to sieze up if the machine hasn't been used for a while. Submitted on 18-1-2022 at 16:46
Reply Report abuse
If my polti 2000 has not been in use for the last 5 years but has been stored correctly, is it possible for the safety cap to become seized up I have tried to open it using the the correct procedure but to no avail. Submitted on 18-1-2022 at 16:33
Reply Report abuse
qdo a tampa de proteção não retorna ao sistema original (gira livre) o que fazer ? Submitted on 18-7-2020 at 13:47
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polti MONDIAL VAP 2000 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polti MONDIAL VAP 2000 Manual

Product: