538670
42
Zoom out
Zoom in
Previous page
1/59
Next page
USER MANUAL
ENG
CYCLING HEART RATE MONITOR
CYCLING HEART RATE MONITOR
Polar S725 offers you the possibility for
infrared communication with Polar training
analysis software. See the instructions from
the CD-ROM set.
S725
S725
Display symbols
With the following accessories you get the most out of your S725
See the glossary for display text interpretation.
Polar Cadence Sensor:
A wireless sensor that measures the speed at which
you turn the pedals of your bicycle.
IR Interface:
The Polar IR interface is designed for communication
between Polar heart rate monitors and Polar software
products. For infrared connection to your PC you need
a Polar IR interface if you do not have an IrDA port in
your PC.
Power Output Sensor:
The Polar Power Output system measures pedaling
power when cycling. It also measures left/right balance
(LRB describes the share of power output of left and
right as a percentage), pedaling Index (describes how
evenly power output was produced during a cycle
round), speed, cadence and distance. If you use the
Power Sensor, you do not need to mount any other
accessories on your bicycle.
Indicates an ongoing heart rate measurement and flashes to the beat of your heart.
Indicates there has not been heart rate reception for at least 5 seconds.
- - Indicates there is no heart rate reception. Bring the wrist unit up to your chest
near the transmitter’s Polar logo.
The wrist unit starts looking for the heart rate signal again.
Options mode: indicates that you are setting the bike functions.
Measuring/Recording mode: indicates that bike 1 or 2 is on.
File mode: indicates cycling information.
In the Time of day display the alarm is on.
Measuring mode: beeps if you are exercising outside your target heart rate zone.
Fitness Test mode: sounds an alarm at the end of the fitness test.
Indicates the Interval Trainer.
Indicates continuous interval (Cont).
Recording mode: indicates the heart rate above the target zone.
Recording mode: indicates the heart rate below the target zone.
The graphic bar consists of five blocks. A flashing block indicates in which level you are
in the Options settings or File recalling loops. Continuously running bars indicate that
the exercise is recorded.
Indicates low battery.
17924519.00 ENG A
Quick Guide
Road Map
Infrared
Communication
Connect
Time of
Day
Measuring
Mode
Recording
Mode
File
Recorded
Information
OK
Scroll Up / Down
STOP - exit the displayed
mode
Options
Keep the Road Map and Quick Guide on the back cover open while reading the manual.
Fit. Test
OwnIndex/
Fitness test
Congratulations on purchasing a Polar Cycling Heart Rate Monitor! We are
proud to assist you in achieving personal fitness and performance goals.
If you want to get even more out of your Heart Rate Monitor during training,
check www.polar.fi for:
the best product and training tips in Polar Personal Trainer
the software updates and other value added service for your S-series
heart rate monitor in Polar Product Support
Monitor
Set
Sound
On/OFF
Help
On/OFF
Units 1/2
Watch
Set
Alarm
Time 1/2
Date
Remind
On/OFF
Exercise
Set
BasicUse, E0
ExeSet 1, E1
E2
E3
E4
E5
Interval
On/OFF
Memory
Set
Rec. Rate
5 Sec
15 Sec
60 Sec
Function
Set
OwnCal
On/OFF
Fit. Test
On/OFF
HR
max
-p
On/OFF
Altitude
On/OFF
Bike
Set
Bike
1/2/OFF
Wheel
size
Cadence
On/OFF
Power
On/OFF
User
Set
kg/lbs
Birthday
Sex
Activity
HR
max
VO
2max
cm/ft inch
How to Start Measuring Your Heart Rate (BasicUse)
1. Place the transmitter around your chest and wet the electrodes. Place the
wrist unit on your wrist.
2. Press and hold the OK button to start the measurement. The stopwatch and
the exercise recording start. Your heart rate will appear in about 15 seconds.
How to Stop Measuring Your Heart Rate
1. Press the stop button. The stopwatch and other calculations stop. Heart rate
measurement continues but exercise data is not recorded into a file anymore.
2. Press the stop button again. The wrist unit returns to the Time of day display.
Stop
exit the
displayed mode
return to the
Time of day display
Signal/Light
OK
start measuring the heart rate
lock in your selection
Down
move backward
reduce the
selected value
Up
move onward
increase the
selected value
Manufactured by:
Polar Electro Oy
Professorintie 5
FIN-90440 KEMPELE
Tel. +358-8-520 2100
Fax +358-8-520 2300
www.polar.fi
Recyclable material.
Dear Customer
The features of this cycling heart rate monitor provide you with the various
ways to customize your exercise sessions so they meet your personal needs.
For more information about the different functions, see the "All that you can
do with your Heart Rate Monitor" section.
Please read this manual carefully to familiarize yourself with the Polar cycling
heart rate monitor. Here is where you can find the information you need to use
and maintain your equipment. The function Road Map on the front cover is a
quick guide to the versatile features of the heart rate monitor. The front cover
also contains the different display symbols. There is a Quick Guide on the back
cover on how to use the buttons of the wrist unit.
Please refer to the glossary for special terms and text explanations.
The alphabetical index will help you quickly find answers to any questions
that you might encounter while using your Polar heart rate monitor.
Thank you for choosing Polar!
CONTENTS
A. Getting going ....................... 5
Heart rate monitor parts . ....................... 5
Buttons and their functions .................... 6
Easy start ................................................... 8
How to prepare the wrist unit ........... 8
Installing the Polar Bike Mount ......... 9
Installing the Polar Speed Sensor ......9
How to put the transmitter on ........11
How to start measuring
your heart rate ................................... 11
How to stop measuring
your heart rate ................................... 12
After exercising.................................. 12
All that you can do with your
Heart Rate Monitor ...............................13
B. How to enter settings ........ 17
User information settings ..................... 18
Exercise settings ..................................... 21
Selecting exercise type .......................... 21
Setting exercise sets .......................... 22
Setting timers ................................ 24
Setting heart rate limits ............... 24
Heart rate limits on/off ................. 25
Setting recovery calculation ......... 26
Setting interval type ..................... 27
Setting number of intervals and
recoveries ....................................... 28
Setting interval recovery .............. 29
Naming exercise sets ......................... 30
Setting recording rate ........................... 31
Turning functions on/off ....................... 33
OwnCal calorie counter on/off......... 33
Fitness test on/off .............................. 34
Predicted maximum
heart rate on/off ................................34
Altitude and thermometer on/off ... 34
Bicycle feature settings ........................ 36
Wheel size .......................................... 37
Cadence on/off ..................................38
Power on/off ...................................... 39
Naming bike 1 or 2 ............................ 40
Monitor settings .................................... 41
Activity/button sound on/off............ 41
Selecting measuring units ................ 41
Help on/off ......................................... 42
Watch settings........................................ 43
Setting alarm .....................................43
Setting time of day ............................ 44
Setting date........................................ 44
Reminders on/off ............................... 45
Setting tips ............................................. 46
Swap time 1 or time 2 ....................... 46
Shortcut to watch settings ............... 46
Swap measuring units ....................... 46
Swap date, user ID number,
user name and logo ..........................46
C. Exercise ................................ 47
Measuring mode .................................... 47
Recording mode ..................................... 50
Heart rate zone alarm on/off ...........51
Swapping the heart rate limits ........ 52
Illuminating the display .................... 52
Storing lap and split time ................. 53
Pausing the exercise .......................... 53
Swapping the displayed
exercise information ......................... 54
Resetting the stopwatch to zero .....56
Starting an exercise set ......................... 56
Exercising with Interval Training Set ... 57
Warm-up phase.................................. 58
Interval phase ....................................58
Cool-down phase ............................... 61
Interrupting an interval
training exercise ................................ 62
Exercising with BasicSet ........................ 62
Starting the timers ............................ 62
Starting the recovery calculation ..... 63
Stopping the exercise ............................ 63
Tips during the exercise ........................ 63
Swapping the exercise type ..............63
Swapping the bike setting ............... 64
Resetting the trip distance ............... 64
Returning to the manually
set altitude ......................................... 64
Restarting the interval or
recovery calculation .......................... 64
Interrupting an interval or
recovery calculation .......................... 65
Interrupting a phase of an
interval training exercise .................. 65
Heart Touch Function ........................ 65
D. How to recall
training information .......... 66
Exercise time ...................................... 68
Recovery information of BasicSet .... 68
Exercise distance ................................ 68
Speed information ............................ 68
Cadence information ........................68
Altitude............................................... 68
Temperature....................................... 69
Ascended meters/feet ....................... 69
A. GETTING GOING
A 5
The elastic strap detects
your heart rate.
The connector transmits
your heart rate signal
to the wrist unit.
The wrist unit displays
your heart rate and
cycling data during
exercise. Enter your
personal settings into
the wrist unit
and analyze the exercise
files after you’re done.
Power ................................................ . 69
Pedaling index ................................... 69
Left right pedaling balance .............. 69
Heart rate limits ................................. 69
Exercise time within, above and
below the heart rate zones .............. 70
Calorie expenditure ........................... 70
Cumulative calorie count .................. 70
Cumulative exercise time count ....... 70
Cumulative riding time ..................... 70
Odometer ........................................... 71
Interval Training information........... 71
Lap information ................................. 73
Recorded samples .............................. 75
Deleting a file .................................... 76
Deleting all files .................................76
Records file ............................................. 77
Resetting cumulative
counts to zero .................................... 78
Returning to your previous
maximum value ................................. 79
E. Polar Fitness Test ................. 80
OwnIndex ............................................... 80
Predicted maximum heart rate............. 82
Fitness test settings ................................83
Carrying out the test ............................. 83
Update OwnIndex and HR
max
-p ............. 85
Fitness classes ......................................... 86
F. Care and maintenance ....... 88
G. Precautions ......................... 93
H. Frequently asked
questions ............................. 97
I. Technical Specifications ... 101
J. Limited Polar International
Guarantee ......................... 104
K. Disclaimer ......................... 105
L. Polar glossary ................... 106
Display texts .........................................107
Index ...................................................... 111
Heart rate monitor
parts and their
functions
A 6 A 7
STOP
SIGNAL
/
LIGHT
OK
Signal/ Light Turns the beep on or off.
Turns the backlight on.
Stop Return - Stops measuring the heart rate.
Exits the displayed mode and returns to
the previous mode level.
Returns to the Time of day display
from any mode by pressing and
holding the stop button.
OK Accept - Starts measuring the heart rate (start).
Enters the displayed mode shown on
the lower level (start). Locks in your
selection (ok). Records lap information
(lap). The Help text (start, ok or lap)
that appears on the display above the
button indicates its use.
Buttons and their functions
Useful tips
Briefly pressing a button (approximately 1 second) will do different
things than pressing and holding the button for a longer period of
time (approximately 2 to 5 seconds). If your press the button for a
longer period of time, you can use shortcuts.
The buttons are slightly stiffer than those of an ordinary watch to
prevent them from being pressed accidentally.
You can always return to the Time of day display from the Options
setting or File recalling loops by pressing and holding the stop button.
Up Moves to the following
mode. Increases the
selected value.
Reset Resets the heart rate
monitor.
Down Returns to the previous
mode. Decreases the
selected value.
A 8 A 9
How to prepare the wrist unit
1. Since the display is blank when the wrist unit leaves the
factory, you have to activate the wrist unit by pressing the
OK button twice, after which the Time of day display
appears. This is a one-off procedure; once you have turned
on your wrist unit you can not turn it off anymore.
2. You may start measuring your heart rate right away
using the default settings. However, the following
settings are ones that it would be useful to change as
soon as possible: Time of day (see section Setting the
watch) and personal user settings (see section User
information settings).
3. Your heart rate monitor has various functions that you can
use according to your personal training needs. For more
information, see section All that you can do with your
Heart Rate Monitor. You can either manually enter the
settings by pressing the wrist unit buttons or you can
define your settings with Polar Precision Performance
software, after which the data should be transferred from
your PC to the wrist unit.
4. Wear the wrist unit as you would wear an ordinary
watch. When you go biking, we recommend attaching the
wrist unit to the Polar Bike Mount™.
Easy start
Installing the Polar Bike Mount™
Use cable ties to secure the bike mount
snugly on the rubber pad.
Attach the wrist unit by securing the wrist strap.
Installing the Polar Speed Sensor™
The Polar Speed Sensor measures speed and
distance when cycling.
1. Check the front side of the front fork to
find a suitable place for the speed sensor.
The sensor should be attached less than
50 cm/ 1’8" from the mounted wrist unit.
The smaller the distance the better. Clean
and dry the area underneath the rubber pad
before you attach it to the front fork.
2. Place the sensor in the position as in
illustration 2. Then adjust the sensor
towards the wheel as much as possible.
3. Pass the cable ties through the sensor
holes and loosely adjust the ties. Do not
tighten fully yet. If the cable ties are too
short for your bicycle, put two of them
together to make them longer.
60°
Riding direction
max 50 cm /
1´8´´
1
2
If you are using Polar S725 with Polar
Power Output Sensor, please see the bike
mount and sensor installation instructions
in the Power Output Sensor user manual. If
you use the Power Sensor, you do not need
to mount any other sensors on your bicycle.
A 10 A 11
4. There are two spoke magnet options.
You only need to install one of them.
Check which of the magnets fits the spoke
of your bike best. One (A) is installed by
rotating it around the spoke before putting
the metal cover on, another (B) by
tightening the screw. The magnet must be
facing the speed sensor.
5. Fine-tune the positioning of both the
magnet and the sensor so that the magnet
passes the sensor closely but does not
touch it. The maximum distance between
the speed sensor and the spoke magnet
should be 5 mm/ 0.2". Once positioned
correctly, tighten the cable ties securely
and cut off any excess cable tie ends.
Your safety is important to us. While riding
your bike, please keep your eyes on the
road to prevent possible accidents and
injury. Check that you can turn the handle
bar normally and cable wires for brakes or
gearing do not catch on the sensor. Check
also that the sensor does not disturb
pedaling or the use of brakes or gearing.
How to put the transmitter on
1. Moisten the electrode areas of the strap
under running water and make sure that they
are well moistened.
2. Attach the connector to the strap. Position
the connector's letter L to the word LEFT on
the strap and snap the fastener.
3. Adjust the strap length to fit snugly and
comfortably. Secure the strap around your
chest, just below the chest muscles, and snap
the second fastener.
4. Check that the wet electrode areas are firmly
against your skin and that the Polar logo of
the connector is in a central, upright position.
5
4
A
B
or
How to start measuring your heart rate
1. Begin with the display that
shows the time of day.
2. Keep the wrist unit within
1 meter/ 3 feet of your
transmitter.
3. Check that you are not near other people
that have heart rate monitors, high voltage
power lines, televisions or other sources of
electromagnetic disturbance. In some cases,
A 12 A 13
mobile phones may cause interference when starting
the heart rate measurement.
4. Press the OK button to start measuring your heart rate.
A heart symbol will start flashing and your heart rate
(beats per minute) will appear in a maximum of 15
seconds.
5. Press OK again. The stopwatch starts running and you
can start exercising. The exercise data will only be
All that you can do with your Heart Rate Monitor
Here is a short overview of the modes of the wrist unit and the different
functions they offer you.
1. TIME OF DAY
In this mode you can use your heart rate monitor as a watch since it can
display the time, date, weekday, alarm and two different time zones. In
addition, you can upload a personal logo, user number or user name
from a PC. You can also upload 7 reminders with alarms.
2. MEASURING MODE (SEE SECTION C. EXERCISE)
In this mode your heart rate is displayed, but exercise information is not
recorded or stored in the File mode. In Measuring mode you can choose
the information that is displayed on the wrist unit during exercise.
3. RECORDING MODE (SEE SECTION C. EXERCISE)
In Recording mode your exercise is recorded and stopwatch and other
calculations are started. You can use the BasicUse function when you
just want to exercise without setting heart rate limits, timers or other
exercise settings. If you use the settings mentioned above, you can
program up to five exercise sets for different kind of exercises.
stored in a file if you have turned the stopwatch on.
How to stop measuring your heart rate
1. Press the stop button. The stopwatch and other calculations stop.
The heart rate measuring continues, although exercise data is no longer
recorded.
2. Press the stop button again. The heart rate measuring stops.
The wrist unit shows the Time of day display again.
After exercising
1. Carefully wash the transmitter with a mild soap and water solution.
2. Rinse it with pure water.
3. Dry the transmitter carefully with a soft towel.
4. Store the transmitter in a clean and dry place. Dirt impairs the elasticity
and functioning of the transmitter. Sweat and moisture can keep the
electrodes wet and the transmitter activated, which shortens battery life.
A 14 A 15
A. BasicUse is the easiest way to start exercising because you do not
have to set different heart rate limits or timers. You just start in
Measuring mode and choose BasicUse and you are ready to go. You can
select among several different heart rate or cycling information
alternatives for the display of your wrist unit.
B. Freely programmable BasicSet offers you the possibility to set
three functions to control your exercise session. 1. Three adjustable
target heart rate limits (either HR or % of HR
max
limit types) 2. Three
adjustable alternating timers. 3. Time-based or heart rate-based
recovery calculation. By using these functions, you can easily control
your normal exercise session. You can program several different kinds of
exercise sets. When training, choose the one that suits the training you
plan to do best.
C. Freely programmable Interval Trainer automatically guides you
through your interval training session. You can program the following
exercise phases:
1. warm-up period with heart rate limits and a countdown timer
2. up to 30 intervals with target heart rate limits and an option for
a recovery calculation after each interval
3. a cool-down period, using a countdown timer after intervals
Use of this Interval Training function leaves you free to concentrate on
your exercise during the interval training. Your heart rate monitor takes
care of observing timers and heart rate limits, all you have to do is
exercise.
4. FILE (SEE SECTION D. HOW TO RECALL TRAINING INFORMATION)
In this mode you can recall your training information. Your heart rate
monitor saves up to 99 files of exercise information when you use the
Recording mode (stopwatch on).
5. OPTIONS (SEE SECTION B. HOW TO ENTER SETTINGS)
In the Options mode you set all your personal settings for optimal use of
your heart rate monitor. It is highly recommended that you enter all
your personal settings in your wrist unit before you start to use your
heart rate monitor for the first time. By doing so, you guarantee the
optimal functioning of your heart rate monitor. You can also use the
Polar Precision Performance software to set and upload your personal
settings from your PC to your wrist unit.
6. TEST (SEE SECTION E. POLAR FITNESS TEST)
In this mode you can carry out the Polar Fitness Test. This test estimates
your maximal aerobic power (VO
2max
) and shows the result as a Polar
OwnIndex value. This test also provides a predicted maximum heart rate
value (HR
max
-p). The Polar Fitness Test is designed to monitor your
personal progress. You should do the test regularly to see the changes
in your cardiovascular fitness. Your heart rate monitor will memorize
your last OwnIndex value.
A 16 B 17
7. CONNECTION (SEE SEPARATE CD-ROM SET)
In Connection mode you can download recorded training information
from your wrist unit's memory to your PC for more elaborated analysis.
You can also upload your wrist unit settings from your PC. To perform
the above-mentioned operations, you need the Polar Precision
Performance software.
B. HOW TO ENTER SETTINGS
Exercise
Set
Memory
Set
Function
Set
Bike
Set
User
Set
Watch
Set
Monitor
Set
Time Of
Day
File
Options
Fit. Test
Connect
This section describes how to manually enter
settings by pressing the wrist unit buttons.
However, Polar heart rate monitor offers you
another and faster way as well: prepare your
settings with Polar Precision Performance
software and upload them to your wrist unit from
your PC. See the separate CD-ROM set for infrared
communication possibilities.
After preparing your settings you can upload options lock from the
Polar Precision Performance software to ensure that your settings will
not change. You must deactivate the options lock from the "user
features" of the software.
B
19B 18
User information settings
Weight (kg or lbs)
5. Scroll up or down to adjust your weight. Press OK.
Height (cm or ft/ inch)
6. Scroll up or down to adjust your height. Press OK.
Date of birth (Birthday)
7. Scroll up or down to adjust your day of birth.
Press OK.
8. Month appears. Scroll up or down to select
your month of birth. Press OK.
9. Year appears. Scroll up or down to adjust the year of birth. Press OK.
Sex
10. Scroll up or down to select your gender. Press OK.
Activity level (Activity)
11. Scroll up or down to select your activity level for Polar Fitness Test. Press OK.
Assess your long-term physical activity level. Do not change your activity level
description if your regular exercise habits have changed during the last six months.
Low You do not participate regularly in programmed recreational sport
or heavy physical activity. E.g. you walk only for pleasure or
occasionally exercise sufficiently to cause heavy breathing or
perspiration.
Middle You participate regularly in recreational sports. E.g. you cycle 15-
30 km per week or spend 1/2-2 hours per week in comparable
physical activity or, your work requires modest physical activity.
User Set
kg/lbs
cm/
feet inch
Birthday
Sex
Activity
HR
max
VO
2max
Options
In the User Set loop you can move forward only by pressing OK.
The digits run faster if you press and hold the up or down button as you
adjust the value. Release the button when approaching the desired value.
Measuring units depend on your choice in Options/ Monitor Set/ Unit 1 or Unit 2.
Units 1 Units 2
Weight kg lbs
Height cm ft/ inch
Date of birth setting order day - month - year month - day - year
As you set your weight and height, adjustable units 1/2 can be
changed by pressing and holding the signal/light button.
1. In the Time of day display scroll up or down until OPTIONS is displayed.
2. Press OK to enter the Options mode. EXERCISE SET
is displayed.
3. Scroll up or down until USER SET is displayed.
4. Press OK to start the user information settings.
Units 2: setting order
is month - day - year.
B
21B 20
High You participate regularly, at least 3 times a week, in heavy physical
exercise. E.g. you cycle 30-60 km per week or spend 2-3 hours per
week in comparable physical activity.
Top You participate regularly in heavy physical exercise at least 5 times
a week. E.g. you exercise to improve performance for competitive
purposes.
Maximum heart rate value (HR
max
)
12. Your age-predicted maximum heart rate value is displayed as a default
setting when you set this value for the first time. If you know your
exact clinically tested current maximum heart rate value, set the
value by scrolling up or down.
13. Press OK.
If you do not know this value, update it in the Fitness Test mode after
having carried out the Polar Fitness Test.
Maximal oxygen uptake value (VO
2max
)
14. The wrist unit suggests value 35 for females and value 45 for males as a
default setting when you set this value for the first time. If you know
your exact clinically tested current maximal oxygen uptake
value, set the value by scrolling up or down.
15. Press OK. USER SET appears.
If you do not know this value, update it in Fitness Test mode after having
carried out the Polar Fitness Test
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
When you start setting your exercise preferences your first choice is to select
whether you want to set your personal exercise set or to exercise with
BasicUse option. If you select to start setting the exercise sets, your second
choice is whether you want to select BasicSet or an Interval
Training Set.
Selecting exercise type
Exercise settings for Recording mode
BasicUse (E0)
BasicUse is a simple mode for
exercising. You do not have to do any
settings before exercising with this
Recording mode. While exercising, you
can see the following optional values:
current heart rate and average
heart rate of the exercise
stopwatch
time of day
split- and lap times
Additionally, you can follow calories
of your exercise session, percentage
of your maximum heart rate and
cycling information, if you have set
all the user information and turned
the functions on.
Exercise set (E1-E5)
During exercising with this mode you
can see the same optional values as
in the BasicUse mode. Additionally,
the exercise set will guide you
through your exercise according to
the settings you have made. You can
also name the exercise sets e.g. after
an exercise type.
You can set following exercise
guiding functions:
3 heart rate limits
(HR or % of HR
max
based)
3 countdown timers
interval function
recovery calculation
B
23B 22
Setting exercise sets
Preset exercise sets ready for five exercise sets; when you start exercising,
just select one of the sets.
Interval Training Set
If you choose interval on, you can
set 3 different exercise phases for
each exercise set in following order:
Warm-up phase
countdown timer 1 On/OFF
heart rate limits 1 On/OFF
Interval phase
interval calculation type: manual,
time-, heart-rate- or distance-
based interval
number of repeated interval
phases
heart rate limits 2 On/OFF
recovery calculation On/OFF
Cool-down phase
countdown timer 3 On/OFF
heart rate limits 3 On/OFF
summary limits On/OFF
If you set the countdown timers of
the phase off, you have to manually
stop the phase.
BasicSet
If you choose interval off, you can set the
following functions to your exercise:
timer 1 On/OFF
timer 2 On/OFF
timer 3 On/OFF
heart rate limits 1 On/OFF
HR or % of HR
max
based limit types
heart rate limits 2 On/OFF
heart rate limits 3 On/OFF
summary limits On/OFF
recovery calculation On/OFF
You should select the timers on
sequentially. E.g. you cannot set
timer 2 on if timer 1 is off.
Your choice of HR or % of HR
max
limit type in limits 1 determines the
way they will be displayed in all other
limits. Only one limit type can be
selected in an exercise set.
Summary limits are not shown or
alarmed during an exercise. The time
spent within/above/below the summary
limits can be seen from the exercise file.
Options
Exercise Set
E0 E1 E2 E3
E5E4
Exercise
Set 1-5
Timer
1
Limits
1
Limits
2
Timer
3
Recovery
Limits
3
Timer/Hr/Dist.
Interval
Repeat
Interval
Timer/Hr/Dist./Manual
Summary
Limits
Interval
On
Interval OFF
(BasicSet)
Limits
3
Limits
2
Limits
1
Timer
1
Timer
2
Timer
3
Timer/Hr
Recovery
Summary
Limits
HR/% of HR
max
1. In the Time of day display
scroll up or down until
OPTIONS is displayed.
2. Press OK to enter the
Options mode. EXERCISE
SET is displayed.
3. Press OK to start the exercise settings. BasicUse E0 or exercise set E1 - E5
is displayed.
4. Scroll up or down until the desired exercise type is displayed. Press OK.
If you chose BasicUse (E0): to return to the Time of day display, press and
hold the stop button and skip the rest of the exercise settings.
If you chose exercise set (E1-E5) Interval On/OFF is displayed.
5. Scroll up or down to turn the interval function on or off. Press OK.
Timer 1 is displayed.
B
25B 24
Setting timers
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until desired timer is displayed. Press OK to start
setting the timer.
7. Scroll up or down to turn the timer on or off. Press OK.
Timer OFF: skip steps 8-9.
8. Scroll up or down to adjust minutes. Press OK.
9. Scroll up or down to adjust seconds. Press OK.
Setting heart rate limits
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until desired limits are displayed.
7. Press OK to start setting the limits.
8. Only when setting limits 1, scroll up or down to choose HR or % of HR
max
based limits. Press OK to select.
9. Lim High appears. Scroll up or down to adjust your upper limit. Press OK.
10. Lim Low appears. Scroll up or down to adjust your lower limit. Press OK.
Your choice of HR or % of HR
max
in limits 1 determines the way they will
be displayed in all other limits. Only one limit type (HR or % of HR
max
)
can be selected in an exercise set.
01020304050
160
140
120
100
80
60
40
limits 1
Heart
rate
Time
limits 2 limits 3
Summary
limits
Time within, above and below limits 1, 2 and 3 is recorded only when
those particular limits are activated.
Time within, above and below summary limits is recorded during the
entire exercise, regardless of which limits are in use.
Turning heart rate limits on/off
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Limits is displayed.
7. Press and hold the signal/light button to turn limits on or off.
Release.
B
27B 26
Setting recovery calculation
You can select 2 optional types of recoveries in a BasicSet:
A. Time-based recovery Ends your recovery as you reach the preset
time.
B. Heart-rate-based recovery Ends your recovery as you reach the preset
heart rate.
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Recovery TIMER/ Hr is displayed.
7. Press OK to start setting recovery calculation on or off.
On/OFF is flashing.
8. Scroll up or down to turn the recovery calculation on or off. Press OK.
OFF: skip steps 9-11.
On: TIMER/ Hr is flashing.
9. Scroll up or down to select recovery timer or heart rate.
Press OK.
A. RecoTime is displayed.
10. Scroll up or down to adjust minutes. Press OK.
11. Scroll up or down to adjust seconds. Press OK. Recovery TIMER appears.
Or
B. RecoHr is displayed.
10. Scroll up or down to adjust the value. Press OK. Recovery Hr appears.
Setting interval type
You can select four optional types of intervals:
A. Time-based interval Ends your interval when you have used
the preset time.
B. Heart-rate-based interval Ends your interval as you reach the
preset heart rate.
When selecting heart-rate-based interval,
recovery calculation must be set on.
C. Distance-based interval Ends your interval as you reach the
selected distance.
D. Manual interval End the interval training session
by pressing and holding OK.
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Interval TIMER/ Hr/ DIST/ MANUAL is
displayed. Press OK to start setting the interval type.
TIMER/ Hr/ DIST/ MANUAL is flashing.
7. Scroll up or down to select the interval type that will be used to end the
interval. Press OK. If you chose manual interval skip steps 8-9.
B
29B 28
Units 2: Adjustable units
are miles and feet.
A. Time-based interval
8. Scroll up or down to adjust minutes. Press OK.
9. Scroll up or down to adjust seconds. Press OK. Interval TIMER appears.
Or
B. Heart-rate-based interval
8. Scroll up or down to adjust the heart rate that will end your interval.
Press OK. Interval Hr appears.
Or
C. Distance-based interval
8. Scroll up or down to adjust kilometers.
Press OK.
9. Scroll up or down to adjust hundreds of
meters. Press OK. Interval DIST appears.
Setting the number of intervals and recoveries (Repeat)
If you start from the Time of day display, repeat steps 1-5.
You can set up to 30 intervals and recoveries (if set on) for an interval phase.
6. Scroll up or down until Repeat is displayed.
7. Press OK to start setting the number.
8. Scroll up or down to adjust the number. Press OK.
Or
If you do not know in advance the number of intervals and recoveries,
select continuous interval. The intervals will succeed until you manually
stop the exercise or until 30 intervals have been made.
8. Scroll down until Cont
appears. Press OK.
Setting interval recovery calculation
You can select 3 optional types of recoveries:
A. Time-based recovery Ends your recovery as you reach the preset time.
B. Heart-rate-based recovery Ends your recovery as you reach the preset
heart rate.
C. Distance-based recovery Ends your recovery as you reach the selected
distance.
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Recovery TIMER/ Hr/ DIST is displayed.
7. Press OK to start setting recovery calculation on or off.
On/OFF is flashing.
8. Scroll up or down to turn the recovery calculation on or off. Press OK.
OFF: skip steps 9-11.
On: TIMER/ Hr/ DIST is flashing.
9. Scroll up or down to select recovery timer, heart rate or distance.
Press OK.
A. RecoTime is displayed.
10. Scroll up or down to adjust minutes. Press OK.
11. Scroll up or down to adjust seconds. Press OK. Recovery TIMER appears.
Or
B. RecoHr is displayed.
10. Scroll up or down to adjust the value. Press OK. Recovery Hr appears.
Or
B
31B 30
Units 2: Adjustable units
are miles and feet.
C. Rec. Dist is displayed.
10. Scroll up or down to adjust kilometers.
Press OK.
11. Scroll up or down to adjust hundreds
of meters. Press OK. Recovery DIST appears.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
Naming exercise sets
You can name the exercises with seven letters, numbers or punctual marks.
The available digits are: 0-9, space, A-Z, a-z, - % / ( ) * + : ?.
1. In the Time of day display scroll up or down until OPTIONS is displayed.
2. Press OK to enter the Options mode. EXERCISE SET is displayed.
3. Press OK. E0-E5 is displayed.
4. Scroll up or down until desired exercise set (E1-E5) is displayed.
5. Press and hold signal/light button. Adjustable letter is flashing.
6. Scroll up or down to select the desired mark. Press OK.
7. Repeat previous step until you have chosen all 7 letters.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
Setting recording rate
1. In the Time of day display scroll
up or down until OPTIONS
is displayed.
2. Press OK to enter the Options mode.
EXERCISE SET is displayed.
3. Scroll up or down until MEMORY SET
is displayed.
4. Press OK to start the memory settings.
Rec. Rate is displayed.
5. Scroll up or down to select the desired
recording rate. As you change the
recording rate you can see the memory
there is left in the lower row.
Press OK.
Options
Rec. Rate 5 Sec/ 15 Sec/ 60 Sec
Memory Set
The recording time of the wrist unit depends on the selected recording rate
(5 s, 15 s, or 60 s). When the memory is full, you can continue exercising but
the exercise is no longer recorded.
B
33B 32
Altitude Speed Cadence Power Rec. Rate 5s Rec. Rate 15s Rec. Rate 60s
On On On On 4 h 57 min 14 h 53 min 59 h 34 min
On On On OFF 8 h 56 min 26 h 48 min 99 h 59 min
On On OFF On 5 h 35 min 16 h 45 min 67 h 01 min
On On OFF OFF 11 h 10 min 33 h 31 min 99 h 59 min
On OFF OFF OFF 14 h 53 min 44 h 41 min 99 h 59 min
OFF On On On 5 h 35 min 16 h 45 min 67 h 02 min
OFF On On OFF 11 h 10 min 33 h 31 min 99 h 59 min
OFF On OFF On 6 h 23 min 19 h 09 min 76 h 37 min
OFF On OFF OFF 14 h 53 min 44 h 41 min 99 h 59 min
OFF OFF OFF OFF 44 h 42 min 99 h 59 min 99 h 59 min
in one file in one file
and total 130 h and total 520 h
The use of exercise sets and lap recording reduces the maximum exercise
times.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
The following table shows the maximum exercise times for each
recording rate.
Options
Function Set
OwnCal
On/OFF
Fit. Test
On/OFF
HR
max
-p
On/OFF
Altitude
On/OFF
1. In the Time of day display scroll up or down until OPTIONS
is displayed.
2. Press OK to enter the Options mode. EXERCISE SET is
displayed.
3. Scroll up or down until FUNCTION SET is displayed.
4. Press OK to start the function settings. OwnCal is displayed.
Turning functions on/off
To set the following functions on you have to set your user information.
If kg/lbs are displayed as you start setting the function on, the wrist unit
points out that you have not set your all user information.
OwnCal calorie counter on/off
If you start from the Time of day display, repeat steps 1-4.
5. Press OK to start setting the OwnCal function. On/OFF starts to flash.
6. Scroll up or down to set the OwnCal on or off. Press OK.
For getting the most accurate OwnCal results, update the VO
2max
setting
and the HR
max
setting with clinically measured values (if available). If you do
not know your clinically measured values perform Polar Fitness Test and
update the OwnIndex and HR
max
-p settings in Fitness Test mode.
B
35B 34
Fitness test on/off
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until Fit. Test is displayed.
6. Press OK to start setting the fitness test. On/OFF starts to flash.
7. Scroll up or down to set the fitness test on or off. Press OK.
Predicted maximum heart rate on/off (HR
max
-p)
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until HRmax-p is displayed.
6. Press OK to start setting the HR
max
-p. On/OFF starts to flash.
7. Scroll up or down to set the HR
max
-p on or off. Press OK.
HR
max
-p can be turned on only if Polar Fitness Test is on.
Altitude and thermometer on/off
If you start from the Time of day display, repeat steps 1-4
5. Scroll up or down until Altitude is displayed.
6. Press OK to start setting the altitude measurement and thermometer.
On/OFF starts to flash.
7. Scroll up or down to set the altitude on or off. Press OK.
If you turned Altitude off, skip the rest of the altitude settings.
8. If you turned Altitude on, “Wait...” appears for a few seconds.
9. Altitude and a flashing number appear. Start adjusting the starting
point altitude. Adjustable units of 1/ 2 can be changed by pressing and
holding the signal/light button.
Scroll up or down until the desired altitude is displayed. Press OK.
It is recommended that you reset the altitude whenever a reliable
reference is available.
To use the thermometer the altitude must be turned on.
To continue setting your settings, press the stop button or to return to the
Time of day display, press and hold the stop button.
B
37B 36
Options
Bike Set
Bike 1/ Bike 2/ Bike OFF
Wheel Size Cadence On/OFF Power On/OFF
ERTRO Wheel size diameter (inches) Wheel size setting (mm)
30-559 26x1.25 1953
35-559 26x1.5 1985
44-559 26x1.75 2030
47-559 26x1.95 2050
26x1 1/8 Tubular 1970
650-20C 1952
622-20 700x20C 2086
622-23 700x23C 2096
622-25 700x25C 2105
700C Tubular 2130
28 (700 B) 2237
Bicycle feature settings Adjusting the wheel size (Wheel)
If you start from the Time of day display, repeat steps 1-5.
6. Start with the display showing Wheel.
7. Press OK to start setting the wheel size.
8. Scroll up or down to adjust the wheel size. Press OK.
You have the following alternatives to find out
the wheel size of your bike:
METHOD 1.
Look at the wheel of your bike and find the wheel diameter printed on it.
On the chart below, find your wheel diameter in inches or in ERTRO
reading and match it to the wheel size in millimeters on the right.
1. In the Time of day display scroll up or down until OPTIONS is displayed.
2. Press OK to enter the Options mode. EXERCISE SET is displayed.
3. Scroll up or down until BIKE SET is displayed.
4. Press OK to start the Bike settings.
5. Choose to start setting the Bike 1 or 2 or turn the bike
features off. Scroll up or down until desired option is
displayed. Press OK. Wheel is displayed. If you selected bike
features off skip the rest of the bike settings.
You can set two bike preferences for the wrist unit. Make the settings
ready for both bikes; when you start exercising, just select bike 1 or 2. As
you take the bike settings 1 or 2 in use speed and distance measuring
functions are always on. Select the bike features off when exercising
without a bicycle. Wheel size settings are a prerequisite for cycling
information.
B
39B 38
Power* on/off
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Power is displayed.
7. Press OK to start setting the Power Output. On/OFF starts to flash.
8. Scroll up or down to set Power Output on or off. Press OK.
OFF: Skip the rest of the Power Output settings.
9. C. weight is displayed. Scroll up or down to adjust the chain weight. Press OK.
10. C. length is displayed. Scroll up or down to adjust the chain length.
Press OK.
11. S. length is displayed. Scroll up or down to adjust the span length.
Press OK.
If you are using the wireless Polar Speed Sensor, set the Power off.
You can find more information about the Polar Cadence and Polar Power
Output Sensor on the back cover of this manual.
METHOD 2.
Mark the tread of the front tire with a line and roll the tire
perpendicular to the ground. You can also use the valve as
a mark. Mark a line on the ground. Move your bike on a
flat surface straight ahead for one complete wheel rotation.
Check that the tire is perpendicular to the ground. Draw
another line on the ground exactly where the mark on the
front tire touches the ground.
Measure the distance between the two lines on the ground.
Substract 4 mm to account for your weight on the bike to
get your wheel circumference.
This is the value you must set on the meter.
*Optional Polar Cadence Sensor or Polar Power Output Sensor required.
mm
- 4 mm
mm
The wheel size is always indicated in millimeters as this is more accurate.
Resetting the monitor enters the default values.
Cadence* on/off
If you start from the Time of day display, repeat steps 1-5.
6. Scroll up or down until Cadence is displayed.
7. Press OK to start setting the Cadence. On/OFF starts to flash.
8. Scroll up or down to set the Cadence on or off. Press OK.
B
41B 40
Options
Monitor Set
Sound On/OFF Units 1/2 Help On/OFF
Monitor settings
1. In the Time of day display
scroll up or down until
OPTIONS is displayed.
2. Press OK to enter the
Options mode. EXERCISE
SET is displayed.
3. Scroll up or down until MONITOR SET is displayed.
4. Press OK to start the monitor settings. Sound is displayed.
Turning activity/button sound on/off
If you start from the Time of day display, repeat steps 1-4.
5. Press OK to start setting the sound. On/OFF starts to flash.
6. Scroll up or down to set sound On or Off. Press OK.
Activity/button sound consists of the button sound and in the Measuring
and Recording modes the following activity sounds: start, stop and lap
recording, phase start, interval phase end and recovery calculation end
sounds. It does not consist of heart rate zone alarms, watch alarm or fitness
test alarm.
Selecting measuring units
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until Units is displayed.
6. Press OK to start setting the units. 1 or 2 starts to flash.
7. Scroll up or down the unit which best suits you. Press OK.
Naming bike 1 and bike 2
You can name the bikes with four letters, numbers or marks.
The number in the right corner indicates, which bike settings are in use.
(b0=Bike OFF, b1=Bike 1, b2=Bike 2)
1. In the Time of day display scroll up or down until OPTIONS is displayed.
2. Press OK to enter the Options mode. EXERCISE SET is displayed.
3. Scroll up or down until BIKE SET is displayed.
4. Press OK to start the bike settings.
5. Scroll up or down until Bike 1 or 2 is displayed.
6. Press and hold signal/light button. Adjustable letter is flashing.
7. Scroll up or down to select the desired mark. Press OK.
8. Repeat previous step until you have chosen all four letters.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
B
43B 42
Options
Watch Set
Alarm Time 1/2 Date Remind On/OFF
1. In the Time of day
display scroll up or
down until OPTIONS
is displayed.
2. Press OK to enter
the Options mode.
EXERCISE SET is displayed.
3. Scroll up or down until WATCH SET is displayed.
4. Press OK to start the watch settings. ALARM is displayed.
Setting alarm
If you start from the Time of day display, repeat steps 1-4.
5. Press OK to start alarm settings.
On/OFF starts to flash.
6. Scroll up or down to set alarm on or off. Press OK.
24h: skip step 7.
7. 12h: AM/PM starts to flash. Scroll up or down to select AM or PM.
Press OK.
8. The hours start to flash. Scroll up or down to adjust the hours. Press OK.
9. The minutes start to flash. Scroll up or down to adjust the minutes.
Press OK.
When the alarm comes on, it will sound for one minute or you can turn it
off by pressing any of the five buttons.
Watch settings
OFF: Skip
steps 7-9.
The units settings affect the following features:
Units 1: Units 2:
User information kg, cm lbs, feet
Date of birth day-month-year month-day-year
Speed km/h mph
Distance km, hundreds of meters miles, feet
Altitude meters feet
Meters ascended meters feet
Temperature °C °F
Wheel size mm mm (Note!)
Power Chain weight g g
Chain length mm mm
Span length mm mm
Turning Help on/off
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until Help is displayed.
6. Press OK to start setting the Help function. On/OFF starts to flash.
7. Scroll up or down to set the Help on or off. Press OK.
If you turn Help on, the flashing arrows guide you to use the correct
buttons in the Options and File modes. During the exercise, when you are
changing the middle row information, you can see the name of the
function for few seconds. The names are also shown as you recall
information on lap and exercise samples in the File mode.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
B
45B 44
12h time mode:
month - day - year
Setting time of day
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until TIME1/ TIME2 is displayed.
6. Press OK to start setting the time of day.
7. Time is flashing. Scroll up or down to select time 1 or time 2. Press OK.
8. 12h/ 24h starts to flash. Scroll up or down to select 12h or 24h
time mode. Press OK. 24h: skip step 9.
9. AM/PM starts to flash. Scroll up or down to select AM or PM. Press OK.
10. The hours start to flash. Scroll up or down to adjust the hours. Press OK.
11. The minutes start to flash. Scroll up or down to adjust the minutes.
Press OK.
Setting date
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until DATE is displayed.
6. Press OK to start adjusting the date.
7. Day appears. Scroll up or down to select the
desired value. Press OK.
8. Month appears. Scroll up or down to select the
desired value. Press OK.
9. Year digits start to flash. Scroll up or down to select the year. Press OK.
Turning reminders on/off
If you start from the Time of day display, repeat steps 1-4.
5. Scroll up or down until REMIND is displayed.
6. Press OK to start setting the reminders.
7. Scroll up or down until desired reminder is displayed. The number of the
reminder is displayed in the corner of the display.
8. Press OK. On/OFF starts to flash.
9. Scroll up or down to set the reminder on or off. Press OK.
You can upload 7 reminders, each including time and name, to your wrist
unit from Polar Precision Performance software.
The reminder sounds an alarm only when time of day is displayed. When
the reminder alarm comes on, it will sound for 15 seconds or you can turn it
off by pressing any of the buttons except the signal/light button. Erase the
reminder text by pressing any of buttons except the signal/light button.
To continue your settings, press the stop button or to return to the Time of
day display, press and hold the stop button.
B 46 C 47
Time of Day
Measuring
Mode
Recording
Mode
C. EXERCISE
Setting tips
Swap time 1 or time 2
In the Time of day display press and hold the down button. Time 1 or
Time 2 is displayed in the uppermost row for a couple of seconds. Displayed
time will now be used in all watch and alarm functions. If you chose time 2,
“2” is displayed in the Time of day display.
Shortcut to watch settings
Press and hold the signal/light button for a couple of seconds to enter to
watch setting loop. Scroll up or down button until the desired watch
function is displayed. Set the function as in the “Watch settings” section.
Swap measuring units
as you set your user information on weight and height.
as you set an Interval Training Set on distance-based interval or recovery.
as you set the altitude reference point.
Press and hold the signal/light button until the units are swapped. Release
the button.
Swap date, user ID number, user name and logo
You are able to set a user ID number, user name and logo by Polar Precision
Performance software. These settings are shown on the upper row of the
Time of day display. You can swap between the user ID, user name, logo
and date by pressing and holding the up button.
You can use two modes in your exercise:
Measuring or Recording mode. In the Measuring
mode you can see your heart rate but your
exercise is not recorded. In the Recording mode
your exercise is recorded and stopwatch and
other calculations are started.
1. Wear the transmitter and the wrist unit as described in “Easy start”
section.
2. To make sure that the code search will be successful:
Keep the wrist unit within 1 meter/ 3 feet of your transmitter.
Check that you are not near other people that have heart rate monitors,
high voltage power lines, televisions or other sources of electromagnetic
disturbance. In some cases, mobile phones may cause interference when
starting the heart rate measurement.
Measuring mode
C 49C 48
If you are not cycling, turn the cycling settings off by pressing and holding
the down button. Repeat until b0 appears. This will give you more memory
capacity.
4. If you want to record cycling information, keep the bike still until
your heart rate appears on the display. Press OK to start recording
your exercise.
Or
If you want to record cycling information without heart rate measurement:
after the heart rate reading 00 appears press OK and start cycling.
The following displays start to alternate, if you have bike 1 or 2 and
altitude settings on, as you enter the Measuring mode.
3. Start from the Time of day display by pressing the OK to start measuring
your heart rate. A heart symbol will start flashing and your heart rate in
beats per minute will appear in max. 15 seconds. The wrist unit returns
automatically to the Time of day display within 5 minutes if there is no
heart rate reception.
The following displays start to alternate, if you have no bike or altitude
settings in use, as you enter the Measuring mode:
Exercise name Memory left Bike OFF Altitude OFF
Time of day
Current
heart rate
Recording rate
BasicUse (E0)/
Exercise set in use
(E1-E5)
No bike in use
Exercise name Memory left Bike name Altitude
S speed C cadence
P power
Time of day
Current
heart rate
Recording rate
BasicUse (E0)/
Exercise set in use
(E1-E5)
bike in use
Underline indicates that
function is set on.
and bike functions
If you are cycling, turn the cycling settings on by pressing and holding the
down button. b1 appears in the right-hand corner of the display. If you
want to change the preset bike 1 (=b1) settings to bike 2 (=b2), press and
hold the down button again. b2 appears.
C 51C 50
Recording mode
Before starting recording, check that you have enough memory left.
This information is displayed in the upper row, in the Measuring mode.
If you are starting from the Time of day display, press and hold OK.
Exercise information will be stored in an exercise file only when the
stopwatch is running. The ongoing recording is indicated with a graphic
bar that runs continuously on the display.
If your preset exercise requires cycling settings, Set Bike is displayed for a
few seconds. In order to start the exercise set you need to select bike 1 or 2 by
pressing and holding the down button until the desired bike is displayed.
The choice is displayed in the lower right corner:
b0= bike off
b1= bike 1 settings on
b2= bike 2 settings on
If there is - - / 00 reading on the display, there is no heart rate reception.
Bring the wrist unit up to your chest near the transmitter’s Polar logo. The
wrist unit starts looking for the heart rate signal again.
In the beginning of your exercise, when it has lasted less than
60 minutes, the exercise time is displayed in minutes and seconds.
When you have exercised more than 60 minutes, the exercise time is
displayed in hours and minutes.
Turning the heart rate zone alarm on/off
Note that you can not use the alarm when Bicycle functions are on.
Note that trip distance is reset by pressing and holding signal/light
button. Therefore Trip should not be displayed in the upper row when
turning zone alarm on/off.
Press and hold the signal/light button.
When appears on the display the zone alarm is on. You will hear a beeping
sound with each heartbeat if your heartbeat is outside the heart rate limit.
If you do not want to use the zone alarm the flashing heart rate reading
indicates if your heartbeat is outside the heart rate limit. This function can
be used if you have set heart rate limits on for Interval Training Set or
BasicSet.
In addition to the alarm you can see:
if you are exercising above heart rate zone.
if you are exercising below heart rate zone.
C 53C 52
Swapping the heart rate limits
Press and hold the up button. Repeat until the desired limits are displayed.
In the Interval Training mode the limits are automatically swapped when
the phase changes to the preset limits.
You have three optional Recording modes depending on the
selected exercise:
BasicUse
Interval Training Set (Int On)
BasicSet (Int OFF)
The following functions can be used during all three optional Recording
modes.
Illuminating the display (Night Mode)
Press the signal/light button in the Measuring or Recording mode. After
you have illuminated the display once, the display automatically illuminates:
at the end of an interval or recovery calculation
if you start or stop the exercise session
if you store lap information
if you bring the wrist unit near the Polar transmitter (Heart touch)
You can turn this function off by pressing the signal/light button again. It is
automatically turned off when you return to the Time of the day display. If
you want to illuminate the display in the Time of the day mode, press the
signal/light button.
Storing lap and split time
Press OK to store lap and split time.
First Then
Lap time Split time
Average heart
rate of the lap
Number of
the lap
The wrist unit automatically stores a lap time when you stop recording
an exercise. You can store 99 laps if you have not used the interval
function. After storing 99 laps FULL appears for a few seconds every
time you take a lap on the display. You can continue taking laps but
they will not be stored. The wrist unit continues recording all other
information of the exercise, except lap and interval information.
Pausing the exercise
Press the stop button.
The exercise recording, stopwatch and other calculations are paused. To
continue them, press OK. Or, to return to the Time of day display, press and
hold the stop button.
The wrist unit automatically returns to the Time of day display within
30 minutes if you forget to quit the heart rate measuring after having
stopped the stopwatch and taken the transmitter off your chest.
C 55C 54
*Optional Polar Cadence Sensor or
Polar Power Output Sensor required.
Remember to attach your wrist unit to the Polar Bike mount in
order to record the correct temperature.
You can configure the middle and upper rows either in the Measuring
and Recording mode.
1. Select the middle row information
Press the down button briefly to select the desired display alternative.
When you swap the middle row information, the upper and lower rows
change also. Continue selecting the upper and lower rows.
2. Select the upper row information
Press the up button to select from the following:
Time of day (Time), stopwatch (Sw), lap time (Lp),
or if you have turned the functions on select from:
calorie expenditure (Cal), trip (Trip), current speed (Spd), average speed
(Avg speed), maximum speed (Max speed), cadence* (Cad), altitude
(Alt), ascended meters (Asc), output power* (Pwr), left right pedaling
balance* (LRB), pedaling index* (PI).
You cannot select the same displayed function to the upper and middle row
i. e. the option on the middle row is no longer available for the upper row.
Swapping the displayed exercise information
You can swap the display information by pressing the down button in the
Measuring or Recording mode. The wrist unit saves the upper and lower
row settings for the display options. If the Help function is on, the name of
the selected function appears for a few seconds. When you start the
exercise next time the stopwatch appears on the middle row and the saved
functions appear on the upper and lower rows.
Phase Name
Countdown
timer
When you have set your Interval
Training Set on, you will have one
extra display. You can only change the
lower row for this display. See the
alternative phase displays from
“Exercising with Interval Training Set”
section.
5. Power*
4. Altitude
Temperature
6. Stopwatch
Time of day
3. Speed
2. Time of day
Lap time
1. Time of day
Stopwatch
Current heart rate
Number of the
lap
C 57C 56
01020304050
160
140
120
100
80
60
40
WarmUp phase
Countdown timer 1
Heart rate limits 1
Interval Phase
Repeats 03
CoolDown phase
Countdown timer 3
Heart rate limits 3
Interval
Recovery
Interval
Recovery
Interval
Recovery
Heart
rate
Time
Structure of an interval training exercise:
Exercising with Interval Training Set (Int On, E1-E5)
In this mode you can also use the functions described in “Recording mode”
section.
The Interval Trainer automatically guides you through your exercise. In
order to hear the activity sounds when the phase starts and stops make
sure the activity sound is on. If you have turned the countdown timer of
the phase off, you have to stop the phase manually by pressing and holding
OK button. When the stopwatch starts running indicates that Interval
Trainer is on. As the interval training exercise ends the wrist unit
automatically starts a BasicUse exercise, which is recorded to the same file
as your interval training exercise.
1. Start from the Time of day display. Press OK to enter the Measuring mode.
2. If you want to swap the preset exercise set, press and hold the up button
until the exercise set (E1-E5) is swapped. Release. Repeat until desired
exercise set is displayed.
3. To start exercising and recording the preset exercise type press OK.
Starting an exercise set
3. Select the lower heart rate information row
Press and hold the down button to select from the following:
Current heart rate, average heart rate (avg) or the reading in
percentages of your maximum heart rate (% max) if you have set your
user information.
You can only change the displayed function of the lower row if the
stopwatch is on.
Resetting the stopwatch to zero
1. Pause your exercise.
2. Press and hold the down button until the stopwatch is reset. Release.
3. Press OK to restart the stopwatch and recording. Or, to return to the
Time of day display, press and hold the stop button. As a result of
resetting your stopwatch, the previous exercise file is deleted.
C 59C 58
Interval session
1. First
Preset heart rate limits 2 (if set on).
2. Then
One of the following is displayed depending on your settings:
A. manual, B. time-based, C. heart rate-based or
D. distance-based interval.
A. Manual interval.
Number of set intervals.
Current interval number.
Interval time.
Heart rate information.
If you selected manual interval your interval will end as you
press and hold OK.
Or
B. Time-based interval.
Countdown timer 2.
If you selected time-based interval your interval will end as
you reach the preset time.
Or
C. Heart-rate-based Interval.
The difference between the preset interval heart rate and
current heart rate.
Or
D. Distance-based interval.
Countdown distance.
Your interval will end as you reach the preset distance.
Warm-up phase
1. First
Heart rate limits 1 (if set on).
2. Then
Countdown timer 1.
Heart rate information.
Countdown timer starts running if you have set the timer 1
on. If you have set the timer off, press and hold OK and
continue from the interval phase.
3. At the end of warm-up phase
Warm-up phase duration.
Average heart rate of the warm-up phase.
Interval phase
The wrist unit records up to 30 repeated interval phases. Your interval
phase is divided into interval and recovery calculation (if set on) sections,
which alternate continuously through your interval phase. As the interval
phase changes, the heart rate limits are automatically swapped. For
example, when the first phase changes to the second phase, the preset
heart rate limits 1 changes to preset heart rate limits 2. You can also swap
the heart rate limits by pressing and holding the up button. Repeat until
the desired limits are displayed.
C 61C 60
3. At the end of Interval
Interval duration.
Average heart rate of the interval.
When your interval ends the wrist unit automatically
continues with following preset function: recovery
calculation or cool-down phase.
Recovery calculation
One of the following is displayed depending on your settings:
A. time-based recovery calculation or B. heart-rate-based
recovery calculation or C. distance-based recovery calculation.
A. Time-based recovery.
Recovery countdown timer.
Current heart rate.
Or
B. Heart-rate-based recovery.
The difference between the preset recovery heart rate and
current heart rate.
Current heart rate.
Or
C. Distance-based recovery.
Recovery countdown distance.
Current heart rate.
You will hear two beeps when the recovery calculation is done.
At the end of recovery
A. and B. Or C.
Recovery duration. Recovery distance.
Drop in your heart rate.
Cool-down phase
1. First
Preset heart rate limits 3 (if set on).
2. Then
Countdown timer 3.
Heart rate information.
Countdown timer starts running if you have set the timer 3 on.
If you have set the timer off, press and hold OK to end a phase.
3. At the end of cool-down phase
Cool-down phase duration.
Average heart rate of the cool-down phase.
After your cool-down phase has ended the wrist unit
automatically continues recording exercise with BasicUse mode.
You can continue using the heart rate limits of the interval
exercise in the BasicUse mode, too. Or, if you want to do
another interval training exercise, press and hold the OK
button.
C 63C 62
Swapping the exercise type (E0 or E1-E5)
In the Measuring mode press and hold the up button. Release. Repeat until
desired exercise set or BasicUse is displayed.
Tips during the exercise
Exercising with BasicSet (Int OFF, E1-E5)
In this mode you can also use the functions in “Recording mode” section.
Starting the timers
If timers are set on, they automatically start running once you start the
stopwatch. Timers alternate in the following order: timer 1, 2, 3, 1, 2, 3 etc.
At the end of timer 1 you will hear 1 beep, at the end of timer 2 you will
hear 2 beeps and at the end of timer 3 you will hear 3 beeps. Timers stop
running when you stop the stopwatch.
1. Press the stop button to pause the exercise.
2. Press and hold the stop button until Time of day is displayed.
Your lap and split time are automatically recorded, when you end the
exercise.
Stopping the exercise
Starting the recovery calculation
To start the recovery calculation, press and hold the OK button.
See “Exercising with Interval Trainer”/ “Recovery calculation” for the
displayed information during the recovery calculation. After the recovery
calculation is done the exercise is paused.
You can continue the exercise by pressing the OK button after the recovery
calculation. If you do another recovery calculation, the previous recovery
information will be deleted.
Interrupting an interval training exercise
1. Press the stop button to pause the exercise.
2. Press and hold the stop button to return to the Time of day display.
Or
Press the stop button. BasicUse appears. You can continue measuring your
heart rate in this mode (Measuring mode). To continue exercising with
BasicUse and recording your exercise information press OK. You can
continue using and swapping the same heart rate limits of the previous
exercise. Repeat steps 1 and 2 to return to the Time of day display.
C 65C 64
Tips during the exercise
Swapping the bike setting (b0, b1 or b2)
Start from the Measuring mode. Press and hold the down button until Bike 1
or 2 or Bike OFF is displayed. You can now start exercising with the chosen
settings. For more information about cycling measurement, see the
“Measuring mode“ and “Swapping the displayed exercise information”
sections.
Resetting the trip distance
Start from the Measuring or Recording mode. Scroll up until Trip is displayed.
Press and hold the signal/ light button until the trip reading is zero. Release.
Returning to the manually set altitude
Start from the Measuring mode. Scroll down until altitude is displayed in
the middle row. Press and hold the signal/light button until the previous
manually set altitude is displayed.
If the manually set altitude reference value deviates over ±610 m/ ±2000 ft
from the altitude calculated by the wrist unit, Failed appears and the
measured altitude appears. Set the reference altitude from the Options
mode. As you start adjusting the reference altitude, the wrist unit suggests
a measured altitude for you instead of the previously set altitude.
Restarting the interval or recovery calculation
In the Recording mode press the stop button to pause the interval or
recovery calculation.
Start resetting by pressing and holding the down button. To restart the
same calculation press the OK button or to reset the interval training
exercise, see “Resetting stopwatch to zero” section.
Interrupting an interval or recovery calculation
Press and hold the OK button during your interval training exercise
session to interrupt the calculation. The following section automatically
starts. E.g. if you interrupt an interval your recovery calculation (if set on)
automatically starts.
Interrupting a phase of an interval training exercise
Press the stop button to pause your phase. Press and hold the OK button.
The following phase automatically starts.
Heart touch function
The heart touch function is activated as you bring the wrist unit near the
transmitter’s Polar logo.
You have three alternatives for the heart touch function. To select heart
touch display, use your Polar Precision Performance software:
Checking the current heart rate limits
Swapping the display options
Storing lap time
During the heart touch, the backlight is on for a couple of seconds, if you
have already used the backlight during the exercise.
D 67D 66
File (F1-F99)
Exe. Time
Distance
Speed
Cadence
Altitude
°C/ °F
Ascent
Power
Pl %
LRB
Limits
InZone 1
InZone 2
InZone 3
InZone S
KCal
Tot. KCal
Tot. Time
Rid. Time
Odometer
EXE SET
LAPS
SAMPLES
Recovery
D. HOW TO RECALL TRAINING
INFORMATION
The wrist unit starts saving exercise information
to a file as you start the stopwatch. You can recall
the information in the File mode. In the File mode
there are up to 99 exercise files and a records file,
which keeps track of the cumulative and maximum
exercise values.
Time of Day File Options Fit. Test Connect
F99 ... F1 Records
Your first file is F1, then F2 and so on, until you have recorded maximum 99
exercise files. The bigger the file number the more recent it is.
Some information alternates on the display automatically.
You can make the alternation faster by pressing the OK button e.g. the
target heart rate zone information.
If a function was not activated in the settings mode, that
information will not be displayed in the recorded file.
Exercise file
1. In the Time of day display scroll up or down until FILE is displayed.
2. Press OK to enter the File mode. The main information of
your file is displayed.
Starting date and time alternate on the display.
Exercise name
File number
Used exercise set
(E1-E5)
or BasicUse (E0)
3. Scroll up or down until the desired file is displayed.
4. Press OK to start recalling an exercise file. Exe. Time is displayed.
Move forward and backward within file loops with
up or down buttons.
Press OK to enter a file or to enter a deeper level in the file loop.
Press the stop button to move backward to the previous file level.
Press and hold the stop button to return to the Time of day
display, wherever you are in the File recalling cycle.
D 69D 68
Temperature (°C or °F Avg/ Max/ Min)
Average, maximum and minimum temperature of the exercise alternate.
Ascended meters/feet (Ascent)
You can see the ascended meters/ feet of the exercise.
Power* (Pwr Avg/ Max)
Average and maximum output power of the exercise alternate.
Pedaling index* (PI Avg/Max)
Average and maximum pedaling index of the exercise alternate.
Left right pedaling balance* (LRB Avg)
You can see the average balance between left and right foot pedaling.
Heart rate limits 1, 2, 3 and summary (Limits 1/ Limits 2/ Limits 3/ Limits S)
Settings of the heart rate limits alternate on the display. Limits 1 are used
for heart rate zone 1, limits 2 for zone 2, limits 3 for zone 3 and limits S for
summary zone.
Summary limits are not shown or alarmed during an exercise. The time
spent within/above/below the summary limits can be seen from the
exercise file.
Exercise time (Exe. Time)
The exercise time is the amount of time that you have exercised
with the stopwatch running. Average and maximum heart
rates of your exercise alternate on the display. To continue
recalling the file, scroll up or down button.
Recovery information of BasicSet exercise (Reco)
Recovery time.
Recovery duration.
Drop in your heart rate.
Or
Recovery heart rate.
Time it took reach the preset heart rate reading.
Drop in your heart rate.
Exercise distance (Exe. Dist.)
You can see the exercised distance.
Speed information (Spd. Avg/ Max)
Average and maximum speed of the exercise alternate.
Cadence information* (Cad. Avg/ Max)
Average and maximum cadence of the exercise alternate.
Altitude (Alt. Avg/ Max/ Min)
Average, maximum and minimum altitude of the exercise
alternate.
*Optional Polar Cadence Sensor or
Polar Power Output Sensor required.
D 71D 70
Odometer
Measures cumulative total distance of several exercise sessions starting
from the previous resetting of the value in records file.
Interval Training information (EXE. SET)
Exercise time within, above and below the heart rate zones
Indicates the exercise time, which you have spent within (InZone), above and
below each heart rate limits. Time within, above and below limits 1,2 and 3
is recorded only when those particular limits are activated. Time within, above
and below summary limits is recorded during the entire exercise, regardless
of which limits are in use.
Calorie expenditure (KCal)
You will see how many kilocalories you have expended during the exercise.
Cumulative calorie count (Tot. KCal)
You will have a count for cumulative calories expended during several
exercise sessions starting from the previous resetting of the value in records
file. This function allows you to follow the calorie count as a gauge of
effective exercise e.g. during one week.
Cumulative exercise time count (Tot. Time)
This function counts cumulative exercise time expended during several
exercise sessions starting from the previous resetting of the value in records
file. It allows you to follow the exercise time count as a gauge of amount
of exercise e.g. during one week.
Your cumulative total time is displayed in hours and minutes until
99 hours 59 minutes is reached. After this your cumulative exercise
time is displayed in hours until 9999 hours is reached.
Cumulative riding time (Rid. Time)
You will have a count for cumulative riding time expended during several
exercise sessions starting from the previous resetting of the value in records
file.
F1-F99
EXE. SET
WarmUp Interval CoolDown
Int 1
Reco 1
...
Int 30 Reco30
Warm-up phase
Warm-up duration.
The heart rate at the end of the warm-up,
average and
maximum heart rates of your warm-up phase.
Interval phase
Interval phase duration.
Average heart rate of intervals and recoveries.
Start with the display
showing EXE. SET.
1. Press OK to start
recalling the interval
training information.
2. Scroll up or down to see
the information on
warm-up, interval and cool-down phases.
D 73D 72
FILE
F1-F99
LAPS
Best Lap
Lap 1
...
Lap 99
Lap information (LAPS)
Start with the display showing LAPS and
the number of recorded laps.
1. Press OK to start recalling the lap
information.
2. Scroll up or down to see the following
information:
Cool-down phase
Duration of the cool-down.
The heart rate at the end of the cool-down,
average and
maximum heart rates of the cool-down phase.
3. Press the stop button to return to the previous file level and skip steps
4-6. Or, continue recalling more detailed information of the interval
phase.
4. Start with the display showing Interval. Press OK to see details of each
interval and recovery.
5. Scroll up or down between intervals (Int) and recoveries (Reco).
Interval information
Interval number. Split time of the interval
Interval duration.
Speed at the end of an
interval (If bike 1/2 was on).
The heart rate at the
end of the interval,
average and
maximum
heart rates of the
selected interval.
Recovery information
Time-based recovery.
Recovery duration.
Drop in your heart rate.
Or
Heart-rate-based recovery.
Time it took reach the preset heart rate reading.
Drop in your heart rate.
Or
Distance-based recovery.
Recovery distance.
Drop in your heart rate.
6. To continue recalling, e. g. , lap information press the stop button twice.
Scroll up or down until LAPS is displayed.
D 75D 74
Recorded samples
Check the detailed information of the exercise in the
sample file.
Start with the display showing SAMPLES and the number
of recorded samples.
1. Press OK to start recalling the samples.
The sample number, heart rate and time when the sample was recorded
are displayed. In the upper row the sample number alternates with the
help texts.
2. The following detailed sample information is shown one by one as you
press OK repeatedly: stopwatch (Stopwatch), speed (Speed), cadence*
(Cadence), altitude (Altitude), power* (Power), left right pedaling
balance* (LRB), pedaling index* (PI %).
3. Scroll up or down from one sample to another.
4. Press and hold stop to return to the Time of day display.
FILE
F1-F99
SAMPLES
S 1
S 2
...
In the upper row, the split time alternates with the help texts if the Help
function is turned on. You can check the following detailed lap
information in the middle row by pressing the OK button repeatedly:
• lap time (Lap Time),
• speed at the end of the lap (Speed),
• cadence* at the end of the lap (Cadence),
• altitude at the end of the lap (Altitude),
• ascended meters at the end of the lap (Ascent),
• power* at the end of the lap (Power),
*Optional Polar Cadence Sensor or Polar Power Output Sensor required.
Laps
Split time.
Lap time.
Lap number.
The heart rate at the end of the lap,
average and
maximum heart rates of the lap.
Best Lap
Shortest lap time.
The number of the best lap.
The best lap information is displayed if you have stored at
least 3 laps. The best lap can not be the last lap.
• left right pedaling balance at the end of the lap* (LRB),
• pedaling index* (PI %),
• ridden distance at the end of the lap (Distance),
• temperature at the end of the lap (°C/ °F).
Press the stop button to exit the LAPS display.
Press and hold stop to return to the Time of day display.
D 77D 76
This file is updated each time your exercise is recorded to file.
1. In the Time of day display scroll up or down until FILE is displayed.
2. Press OK to enter the File mode.
3. Scroll up or down until Records is displayed.
4. Press OK to enter the records file. Tot. KCal is displayed.
You will have a count for cumulative calories expended
during several exercise sessions.
5. Scroll up or down to see the following values:
• cumulative exercise time (Tot. Time)
• cumulative riding time (Rid. Time)
• cumulative riding distance (Odometer)
• maximum speed (Max Spd.)
• maximum cadence* (Max Cad.)
• maximum altitude (Max Alt.)
• maximum power* (Max Pwr.)
You can now return to the Time of day display by pressing and holding the
stop button, continue resetting your cumulative counts or return to your
previous maximum value.
Records file
Deleting a file
1. In the Time of day display scroll up or down until FILE is displayed.
2. Press OK to enter the File mode.
3. Scroll up or down until desired exercise file is displayed. Press and hold
the signal/light button. DELETE FILE and file number are displayed.
4. Press OK. The wrist unit confirms if you want to delete a file
(Are you sure).
5. Press OK to delete the selected file.
6. Press stop to exit the file. Wait appears. The wrist unit rearranges your
file, which takes few seconds.
7. Repress stop to return to the Time of day display.
Deleting all files
1. In the Time of day display scroll up or down until FILE is displayed.
2. Press and hold the signal/light button. DELETE FILES is displayed.
3. Press OK. The wrist unit confirms if you want to delete all files
(Are you sure).
4. Press OK to delete all exercise files.
5. Press stop to return to the Time of day display.
*Optional Polar Cadence Sensor or Polar Power Output Sensor required.
D 79D 78
Resetting your cumulative counts to zero
Once your have reset the cumulative count you cannot retrieve it.
Start with the display showing Tot. KCal, Tot. Time, Rid. Time or Odometer
in the records file.
1. Press OK to start resetting the desired total count. Reset appears and the
value starts to flash.
2. Press and hold the down button. Reset starts to flash. You can still cancel
the resetting by releasing the down button before the value is reset. If
you are sure that you want to reset the value keep holding the down
button until value is reset. Release.
3. Press the stop button to exit the reset display.
Press and hold the stop button to return to the Time of day display.
Returning to your previous maximum value
Start with the display showing Max Spd, Max Cad*, Max Alt or Max Pwr* in
the records file.
1. Press and hold the signal/light button to start returning to the previous
value. Return OLd appears and the value starts to flash.
2. You can still cancel the reset by pressing the stop button. If you are sure
you want to return to the previous value, press OK.
3. Press the stop button to exit the display.
Or, if you want to start resetting your maximum value to zero, press and
hold the signal/light button. Reset VALUE starts to flash. Once your have
reset the value you cannot retrieve it.
4. You can still cancel the reset by pressing the stop button. If you are sure
you want to return to the previous value, press OK.
5. Press and hold the stop button to return to the Time of day display.
*Optional Polar Cadence Sensor or Polar Power Output Sensor required.
E 80 E 81
E. POLAR FITNESS TEST
The Polar Fitness Test is an easy, safe and quick
way to estimate individual maximal aerobic
power and to get predicted maximum heart rate
value. The Polar Fitness Test is targeted to healthy
adults.
OwnIndex
If you want to improve your cardiovascular fitness, it takes a minimum of
6 weeks on an average to see a noticeable change in OwnIndex. Less fit
individuals see progress even more rapidly and for more fit individuals
more time is needed.
Cardiovascular fitness is best improved by exercise types which employ
large muscle groups. Such activities include running, swimming, rowing,
skating, cross-country skiing, cycling and walking.
To monitor your fitness progress start with measuring your OwnIndex a
couple of times during the first two weeks, to get a baseline value.
Thereafter, repeat the test approximately once a month.
OwnIndex is based on resting heart rate, heart rate variability at rest, age,
gender, height, body weight and self-assessed physical activity.
OwnIndex is a value which is comparable to maximal oxygen uptake (VO
2max
),
a commonly used descriptor of aerobic fitness. Cardiovascular (aerobic)
fitness relates to how well your cardiovascular system works to transport
and utilize oxygen in your body. The stronger and more efficient your heart
is, the better the cardiovascular fitness is. VO
2max
is a good indicator of
performance in endurance sports.
E 82 E 83
To get reliable test results, the following basic requirements apply:
You should be relaxed and calm.
The test can take place anywhere - home, office, health club - as long as
the testing environment is peaceful. No disturbing noises (e.g. television,
radio or telephone), no other people talking to you.
Keep the testing place, time of day and environment the same every
time the test is repeated.
Avoid eating a heavy meal or smoking 2-3 hours prior to testing.
Avoid heavy physical effort, alcoholic beverages or pharmacological
stimulants on the test day and the day before.
Carrying out the test
To be able to carry out the Polar Fitness Test you need to do the following
settings in the Options mode:
Set your personal user information and long-term physical activity level.
Set the Polar Fitness Test on.
Set the HR
max
-p on if you want to get a prediction of your
maximum heart rate.
Fitness test settings
The HR
max
-p definition is carried out simultaneously with the Polar Fitness
Test.
The HR
max
-p score predicts your individual maximum heart rate value more
accurately than the age-based formula (220 - age). The age-based method
provides a rough estimation and is thus not very accurate, especially for
people who have been fit for many years or for older people. The most
accurate way of determining your individual maximum heart rate is to have
it clinically measured (in maximal treadmill or bicycle stress test) by a
cardiologist or an exercise physiologist.
Your maximum heart rate changes to some extent in relation to your
fitness. Regular exercise tends to decrease HR
max
whereas reduced training
tends to increase it. There may also be some variation according to the
sport you participate in. For example, running HR
max
> cycling HR
max
>
swimming HR
max
.
HR
max
-p gives the possibility of defining training intensities as percentages
of maximum heart rate and of following maximum heart rate changes due
to training, without an exhaustive maximal stress test. HR
max
-p is based on
resting heart rate, heart rate variability at rest, age, gender, height, body
weight and maximal oxygen uptake, VO
2max
(measured or predicted). The
most accurate HR
max
-p is obtained by entering your clinically measured
VO
2max
into the wrist unit.
Predicted maximum heart rate (HR
max
-p)
E 84 E 85
Time of Day File Options Fit. Test Connect
Fitness Test
Interrupt the test
You can stop the test any time during the test by pressing the stop button.
Failed TEST is displayed for a few seconds.
The latest OwnIndex and HR
max
-p are not replaced.
If the wrist unit does not succeed in receiving your heart rate at the
beginning or during the test, the test will fail. Check that the transmitter
electrodes are wet and the elastic strap is snug enough.
1. In the Time of day display scroll up or down until FIT. TEST is displayed.
If you cannot find Fitness Test mode check that you have turned the
function on in the Options mode.
2. Press OK to enter the Fitness Test mode. Your latest OwnIndex and the
testing date are displayed.
3. Scroll up or down to see your latest HR
max
-p and the testing date.
4. Lie down and relax yourself for 1-3 minutes before the test.
Start the test
It takes 3-5 minutes to carry out the test.
5. Press OK to start the test. The wrist unit starts searching for your
heart rate. TEST On and your heart rate are displayed. The test begins.
6. Lie relaxed. Keep your hands beside your body and avoid body
movements. Don’t communicate with other people.
7. Your current OwnIndex and the testing date are displayed.
8. If HR
max
-p is on: Scroll up or down to see the HR
max
-p result and the
testing date.
Turn the Fitness test sound signal on/off
The sound signal will alarm you at the end of the test. If the sound signal is
on appears on the display.
To turn the sound signal on or off either before or during the test, press
and hold the signal/light button.
You can update your OwnIndex and HR
max
-p values to the Options mode/
User information. When you update these values regularly, the reading in
percentages of your maximum heart rate and calorie calculation give more
accurate individual information.
1. In the Time of day display scroll up or down until TEST is displayed.
2. Press OK to enter the Fitness Test mode.
3. Scroll up or down until Update USER SET is displayed. This display
appears if you have not updated your latest test results.
4. Press OK to update the OwnIndex and HR
max
-p values.
5. To return to the Time of day display, press and hold the stop button.
Your maximum heart rate value is updated if the HR
max
-p is on.
Update OwnIndex and HR
max
-p
E 86 E 87
For various fitness classes we recommend the following:
1
2
3
4
6
7
5
1-3 Increase exercise
for health
benefits and
fitness
improvement.
4 To ensure good health,
maintain current exercise
habits. For fitness
improvement an increase in
exercise is recommended.
5-7 Maintain current
exercise habits
for good health
and fitness.
Top athletes typically score OwnIndex values above 70 (men) and 60
(women). As high values as 95 can be reached by Olympic level athletes.
OwnIndex is highest in sports that involve large muscle groups such as
cross-country skiing and cycling.
The classification is based on literature review of 62 studies where VO
2max
was measured directly in
healthy adult subjects in the USA, Canada and 7 European countries. Reference: Shvartz E, Reibold
RC: Aerobic fitness norms for males and females aged 6 to 75 years: a review. Aviat Space Environ
Med; 61:3-11, 1990.
Fitness classes
The Polar Fitness Test result, your OwnIndex, is most meaningful when
comparing your individual values and changes in them. OwnIndex can also
be interpreted according to your gender and age. Locate your OwnIndex on
the table to find out your current cardiovascular fitness classification,
compared with those who are of the same age and gender.
Age1234567
(years) (very (poor) (fair) (average) (good) (very (excellent)
poor) good)
20-24 < 32 32-37 38-43 44-50 51-56 57-62 >62
25-29 < 31 31-35 36-42 43-48 49-53 54-59 >59
30-34 < 29 29-34 35-40 41-45 46-51 52-56 >56
35-39 < 28 28-32 33-38 39-43 44-48 49-54 >54
40-44 < 26 26-31 32-35 36-41 42-46 47-51 >51
45-49 < 25 25-29 30-34 35-39 40-43 44-48 >48
50-54 < 24 24-27 28-32 33-36 37-41 42-46 >46
55-59 < 22 22-26 27-30 31-34 35-39 40-43 >43
60-65 < 21 21-24 25-28 29-32 33-36 37-40 >40
20-24 < 27 27-31 32-36 37-41 42-46 47-51 >51
25-29 < 26 26-30 31-35 36-40 41-44 45-49 >49
30-34 < 25 25-29 30-33 34-37 38-42 43-46 >46
35-39 < 24 24-27 28-31 32-35 36-40 41-44 >44
40-44 < 22 22-25 26-29 30-33 34-37 38-41 >41
45-49 < 21 21-23 24-27 28-31 32-35 36-38 >38
50-54 < 19 19-22 23-25 26-29 30-32 33-36 >36
55-59 < 18 18-20 21-23 24-27 28-30 31-33 >33
60-65 < 16 16-18 19-21 22-24 25-27 28-30 >30
MENWOMEN
Never put the connector in a washing machine or a drier!
You can wash the strap in a washing machine at +40° C / 104° F. We
recommend that you use a washing pouch.
We recommend that you wash the strap after each time you have used
it in pool water with a high chlorine content.
Do not spin-dry the strap!
Do not put the strap in a dryer!
Do not iron the strap!
Keep the air pressure channels (three openings on the wrist unit backcover)
clean to make sure that the altitude and temperature measurements
work. Do not insert any objects into the openings.
Do not immerse the speed sensor in water.
Avoid hard hits to the speed sensor as these may cause damage.
Batteries
Transmitter
The estimated average battery life span of the transmitter is 2 years
(1h/day, 7 days/week). If your transmitter stops working, it might be due
to the battery running out. We recommend that you have the battery
replaced by an authorized Polar Service Center only.
You can, however, change the battery yourself by following the
instructions below. To change the battery, you need a coin, a sealing
ring and a battery (CR2025).
1. Open the connector's battery cover by turning it counterclockwise with
the coin from the CLOSE position to the OPEN position. The cover pops
out from its niche.
F 89
F. CARE AND
MAINTENANCE
Your Polar heart rate monitor is a high-tech instrument of
superior design and workmanship and should be treated with
care. The suggestions below will help you fulfill the guarantee
obligations and enjoy this product for many years to come.
Taking care of your Polar heart rate monitor
Store your Polar heart rate monitor and transmitter in a cool and dry
place. Do not store it in any kind of non-breathing material, such as a
plastic bag or a sports bag if it is wet. Sweat and moisture can keep the
transmitters electrodes wet and the transmitter activated, which shortens
the battery life.
Keep your Polar heart rate monitor and transmitter out of extreme cold
(below -10 ºC / 14 ºF) and heat (above +50 ºC / 122 ºF).
Do not expose the Polar heart rate monitor and transmitter to direct
sunlight for extended periods, such as by leaving it in a car.
Clean the connector regularly after use with a mild soap and water solution.
Never use alcohol or any abrasive material such as steel wool or cleaning
chemicals on any part of the transmitter.
Do not dry the connector in any other way than with a towel. Rough
handling may damage it.
F 88
2. Remove the battery cover from the connector, lift the battery from the
niche and replace it with a new battery.
3. Remove the sealing ring of the battery cover and replace it with a new
ring.
4. Place the negative (-) side of the battery against the connector and the
positive (+) side against the cover.
5. Put the battery in the connector's niche and put the cover on so that the
arrow points to the OPEN position. Make sure that the cover's sealing
ring is placed correctly in its groove.
6. Gently press the cover deep enough so that its exterior surface is on the
same level as the connector's surface.
7. Turn the cover clockwise so that the arrow on the cover turns from OPEN
to CLOSE. Make sure that the cover is closed properly!
In order to ensure the maximum life span of the connector’s battery
cover, open it only when you need to change the battery. We
recommend that you change the sealing ring of the battery cover every
time you change the battery. You can get the sealing ring/battery kits
from well-equipped Polar retailers and authorized Polar Services. In the
USA and Canada: Additional sealing rings are available from an
authorized Polar Service Center only.
Wrist unit
The estimated average battery life of the wrist unit is 2 years in normal
use (2h/ day, 7 days a week). Note also that excessive use of the backlight
and the alarm signals will use the battery more rapidly. Do not open the
Polar wrist unit yourself. To ensure the water resistance properties and
the use of qualified components, the wrist unit battery should be
replaced only by an authorized Polar Service Center. At the same time a
full periodic check of the Polar heart rate monitor will be done.
Battery Replacement for Speed Sensor
The estimated average battery life of the speed sensor is 2500 hours of
use. We highly recommend you send the speed sensor to an authorized
Polar Service Center for battery replacement, where the unit is tested
after the battery has been replaced. However, if you prefer changing
the battery yourself, please follow these instructions carefully:
Detach the sensor from your bicycle.
1. Open the sensor by removing the two small screws, counter-clockwise,
with a small screwdriver.
2. Lift the case off carefully. Hold the sensor cover upwards so that the
PCBA (printed circuit board assembled) stays in the case.
3. Remove the PCBA carefully.
4. Press the battery holder gently. Release a hook of the holder from
the opposite side of the PCBA and lift the holder upwards. Remove
the old battery.
5. Insert a new battery with the plus (+) side facing up and press the
battery housing gently so that it is attached to the PCBA at all corners.
F 91F 90
G. PRECAUTIONS
G 93
6. Put the PCBA back into place.
7. Check that the sealing ring stays in its groove. Replace the cover back.
8. Insert the two screws in their holes and tighten them gradually in turn.
9. Test the sensor by checking that it gives out an orange flash when the
spoke magnet passes the speed sensor.
10. Do not throw the replaced battery away with normal waste; take it to a
place where problem waste is handled.
Service
Should your Polar heart rate monitor need service, see Customer Care
Charter to contact an authorized Polar Service Center.
Water resistance cannot be guaranteed after unauthorized service.
F 92
Using the Polar heart rate monitor in a water environment
Your Polar heart rate monitor is water resistant to 20 meters/ 60 feet. To
maintain the water resistance, do not operate the buttons of the wrist unit
under water.
Users measuring their heart rate in water may experience interference for
the following reasons:
Pool water with a high chlorine content and seawater are very
conductive. The electrodes of a Polar transmitter may short circuit, which
prevents the transmitter unit from detecting ECG signals.
Jumping into water or strenuous muscle movement during competitive
swimming may cause water resistance that shifts the transmitter on the
body to a location where it is not possible to pick up an ECG signal.
ECG signal strength is individual and also varies depending on an
individual’s tissue composition. The percentage of people who have
problems measuring their heart rate is considerably higher in water than
in other environments.
G 95G 94
Electromagnetic interference
Disturbances may occur near high voltage power lines, traffic lights,
overhead lines of electric railways, electric bus lines or trams, televisions,
car motors, bike computers, some motor driven exercise equipment, mobile
phones or when you walk through electric security gates.
Exercise equipment
Several pieces of exercise equipment with electronic or electrical
components such as LED displays, motors and electrical brakes may cause
interfering stray signals. To try to tackle these problems, relocate the Polar
wrist unit as follows:
1. Remove the transmitter from your chest and use the exercise equipment
as you would normally.
2. Move the wrist unit around until you find an area in which it displays no
stray reading or flashing of the heart symbol. Interference is often worst
right in front of the display panel of the equipment, while the left or
right side of the display is relatively free of disturbance.
3. Put the transmitter back on the chest and keep the wrist unit in this
interference-free area as far as it is possible.
4. If the Polar heart rate monitor still does not work with the exercise
equipment, this piece of equipment may be electrically too noisy for
wireless heart rate measurement.
Polar heart rate monitor and interference
Exercise may include some risk, especially for those who have been sedentary.
Before starting a regular exercise program you are recommended to
answer to the following questions for health status checking. If the answer
is yes to any of the questions, we recommend to consult a doctor before
starting an exercise program.
Have you not exercised for the past 5 years?
Do you have high blood pressure?
Do you have high blood cholesterol?
Do you have symptoms of any disease?
Are you taking any blood pressure or heart medication?
Do you have a history of breathing problems?
Are you recovering from a serious illness or medical treatment?
Do you use a pacemaker or another implanted electronic device?
Do you smoke?
Are you pregnant?
Note that in addition to exercise intensity, heart, blood pressure, psyche,
asthma, breathing etc. medication as well as some energy drinks, alcohol
and nicotine, can affect heart rate.
It is important to be sensitive to your body’s reactions during
the exercise. If you feel unexpected pain or tiredness regarding your
exercise intensity level, it is recommended to stop the exercise or
continue at a lighter intensity.
Minimising possible risks in exercising with a heart rate monitor
H. FREQUENTLY ASKED
QUESTIONS
H 97G 96
What should I do if...
...I don’t know where I am in the Options or File cycle?
Press and hold the stop button until time of day is displayed.
...I cannot find the previous exercise’s file?
You may have used the Measuring mode during your exercise, which means
that your exercise was not stored. To record the exercise you have to turn
the stopwatch on by pressing the OK button in the Measuring mode.
...I cannot find the expended calories from my exercise file?
Check that you have set your personal user information and turned the
OwnCal function on. Check that your heart rate has reached over 90 bpm
or above 60 % of your maximum heart rate during your exercise.
...I cannot turn my HR
max
-p on?
Check that you have set your personal user information and turned the
Fitness Test on before turning the HR
max
-p on.
...there is no heart rate reading (- -)?
1. Check that the electrodes of the transmitter are moistened and
that you are wearing it as instructed.
2. Check that you have kept the transmitter clean.
Notice to persons with pacemakers, defibrillator or other
implanted electronic device. Persons who have a pacemaker use the
Polar heart rate monitor at their own risk. Before starting use, we always
recommend an exercise test under doctor’s supervision. The test is to ensure
the safety and reliability of the simultaneous use of the pacemaker and the
heart rate monitor.
If you are allergic to any substance that comes into contact with
the skin or if you suspect an allergic reaction due to using the
product, check the listed materials in the "Technical Specifications"
chapter. To avoid any skin reaction risk with the transmitter, wear it over a
shirt. However, moisten the shirt well under the electrodes to ensure
flawless operation.
The combined impact of moisture and intense abrasion may cause a
black color, which might stain light-colored clothes especially, to come
off the transmitter's surface.
H 99
H 98
3. Check that you are not near other people that have heart rate monitors,
high voltage power lines, televisions, mobile phones or other sources of
electromagnetic disturbance.
4. Have you had a cardiac event which may have altered your ECG
waveform? In this case consult your physician.
...heart symbol flashes irregularly?
1. Check that the wrist unit is not further than 1 meter/ 3 feet from the
transmitter.
2. Check that the elastic strap has not become loose during exercise.
3. Make sure that the electrodes of the transmitter are moistened.
4. Make sure that there is no other heart rate transmitter within
1 meter/ 3 feet.
5. Cardiac arrhythmia may cause irregular readings. In this case consult
your physician.
...other person with heart rate monitor is causing interference?
Your training partner may have exactly the same code as you. In this case
proceed as follows: Keep a distance from your training partner and
continue your training session normally.
Or
1. Take the transmitter off your chest for 30 seconds. Keep a distance from
your training partner.
2. Put the transmitter back and bring the wrist unit up to your chest near
the transmitter’s Polar logo. The wrist unit starts looking for a heart rate
signal again. Continue your training session normally.
...heart rate reading becomes erratic or extremely high?
You may have come within range of strong electromagnetic signals which
cause erratic readings. Check your surroundings and move further away
from the source of disturbance.
...the display is blank or fading?
If the display is blank, activate the wrist unit by pressing the OK button
twice, after which the Time of day display appears. The first sign of a
discharged battery is the battery symbol on the display. Also the digits fade
when the backlight is used. Have the batteries checked.
...there are no reactions to any buttons?
Reset the Polar heart rate monitor. Resetting clears watch settings which
will return to the default settings. User information and measuring
units settings will be saved.
1. Press the RESET button with a pen tip. Display becomes full of digits.
If you don’t press any button after reset within one minute the wrist
unit returns to the Time of day display.
2. Press any of the buttons once. Time of day is displayed.
...the battery of the wrist unit must be replaced?
We recommend having all service done by an authorized Polar Service
Center. The guarentee does not cover damage or consequential damage
caused by service not authorized by Polar Electro. Polar Service will test
your wrist unit for water resistance after battery replacement and make a
full periodic check of the complete Polar Heart rate monitor.
...there are irregular speed, distance or heart rate readings?
You may have come within range of strong electromagnetic-signals, which
cause erratic readings. Check your surroundings and move away from the
source of disturbance.
I. TECHNICAL
SPECIFICATIONS
I 101H 100
Polar S725 is designed to indicate the level of physiological strain and
intensity in sports and exercise. It also measures altitude and temperature
in cycling. No other use is intended or implied. The altitude and temperature
functions are not designed to be exclusive measuring equipment in aviation,
climbing sports, water sports or their equivalent. Heart rate is displayed as
number of heartbeats per minute (bpm).
Transmitter
Connector
Battery type: CR 2025
Battery sealing ring: O-ring 20.0 x 1.0
Material FPM
Battery life: Average 2 years (1h/ day, 7 days/ week)
Operating temperature: -10 °C to +50 °C/ 14 °F to 122 °F
Material: Polyamide
Water resistance: Water resistant up to 30 m/ 100 feet
Strap
Material: Polyurethane, polyester, polyamide, nylon and
natural rubber including a small amount of latex
...the speed reading is 00 or there is no speed reading on the
display while cycling?
1. Check the correct position and distance of the speed sensor with the
spoke magnet and the wrist unit.
2. Check that you have set bike 1 or 2 on.
3. If the 00 reading appears irregularly, this may be due to temporary
electromagnetic interference in your current surroundings.
4. If the 00 reading is constant, you may have exceeded 2500 riding hours
and the battery of the speed sensor needs to be replaced.
5. If you are using the wireless Polar Speed Sensor, check that Power is
turned off in the Options mode.
...inaccurate altitude readings?
The influence of a sudden temperature change (i.e., if you go outdoors in
the winter) may cause temporarily inaccurate altitude readings. If the
readings are constantly inaccurate, it may be caused by dirt blocking the air
pressure channels (three openings on the backcover of the wrist unit). In
this case, send the heart rate monitor to a Polar Service Center.
...the data transfer from wrist unit to PC was unsuccessful?
1. Check the correct position of the wrist unit with the infrared window of
the PC or the optional interface.
2. Check that the surroundings are not too bright. This problem
often occurs near windows.
3. Check that there is no obstruction between the infrared windows.
Default Settings
Time of day 24h
Alarm OFF
Date of Birth 0
(adjustable range for
year is 1921 – 2020)
Sex male
Weight 0 (kg)
Height 0 (cm)
Activity Low
HR
max
220-age
VO
2max
male 45
female 35
Bike 1/2 OFF
Wheel size for bike 1 2000
Wheel size for bike 2 2100
Cadence OFF
Power OFF
Activity sound On
Units 1
Help On
OwnCal OFF
Fitness test On
HR
max
-p OFF
Altitude OFF
Interval function OFF/
interval
timer
Interval heart rate 160
Interval distance 2 km
Number of intervals 3
Timer 1, 2, 3 OFF/ 2 minutes
Limits 1, 2, 3 and
summary 80/ 160
Recovery function OFF/
recovery timer
Recovery heart rate 80
Recovery timer 1 min
Recovery distance 1 km
Heart touch
function Shows heart
rate limits
Recording rate 5 s
Limit Values
Exercise time 99 h 59 min 59 s
Heart rate limits 30 - 240
Target zone time 99 h 59 min 59 s
Recovery time 99 min 59 s
Calories 99999 kcal
Cumulative calories 999999 kcal
Cumulative
exercise time 9999 h
Riding time 9999 h
Odometer 999 999 km/ miles
Files recorded
to memory 99
Laps recorded
to memory 99
Interval phases
recorded to
memory 30
Temperature
measurement - 10 °C to +50 °C
14 °F to 122 °F
I 103
I 102
Wrist unit
Battery type: CR 2354
Battery life: Average 2 years (2h/ day, 7 days/ week)
Operating temperature: -10 °C to +50 °C/ 14 °F to 122 °F
Water resistance: to 20 meters/ 60 feet
Back cover material: Polycarbonate and glass fibre
Wrist strap material: Polyurethane
Wrist strap buckle and two openings on the back cover are stainless steel
complying with EU Directive 94/27/EU and its amendment 1999/C 205/05 on
the release of nickel from products intended to come into direct and
prolonged contact with the skin.
Watch accuracy better than ± 0,5 seconds/ day at +25 °C/ 77 °F temperature.
Polar S725 is a Class 1 Laser Product.
Accuracy of heart rate measurement: ±1% or ±1 bpm, whichever larger,
definition applies to steady state conditions.
Altitude and temperature measurement: The Polar S725 calculates altitude
by using the standard average altitude in certain air pressures according to
the ISO 2533. The air pressure is measured and the temperature is
compensated every second. The wrist unit displays altitudes between -
448 m - 7590 m or between - 1600 ft - 24900 ft with at least a 1 m / 3 ft
resolution. The reference point’s adjustable altitude range is ± 610 m/ 2000 ft
from the last measured value.
Speed sensor
Operating temperature: -10 °C to +50 °C/ 14 °F to 122 °F
Battery type: CR 2032
Battery life: average 2500 hours of use
Accuracy: ±1 %
Splash proof
K. POLAR
DISCLAIMER
The material in this manual is for informational purposes only. The
products it describes are subject to change without prior notice, due to
the manufacturer’s continuous development program.
Polar Electro Inc. / Polar Electro Oy makes no representations or
warranties with respect to this manual or with respect to the products
described herein. Polar Electro Inc. / Polar Electro Oy shall not be liable
for any damages, losses, costs or expenses, direct, indirect or incidental,
consequential or special, arising out of, or related to the use of this
material or the products described herein.
This product is protected by one or several of the following patents:
US 6277080, FI 111514, GB 2326240, US 6199021, US 6356848, US 6361502,
US 6537227, US 6229454, EP 836165, FI 100924, FI 68734, DE 3439238,
GB 2149514, HK 812/1989, US 4625733, FI 88223, DE 4215549, FR 92.06120,
GB 2257523, HK 113/1996, SG 9591671-4, US 5491474, FI 88972,
FR 92.09150, GB 2258587, HK 306/1996, SG 9592117-7, US 5486818,
FI 96380, US 5611346, EP 665947, DE 69414362, FI 4150, DE 20008882.3,
US 6477397, FR 0006504, FI 4069, DE 29910633, GB 2339833, US 6272365,
FI 107776, US 6327486, FI 110915.
Other patents and design patents in pending.
K 105
J. LIMITED POLAR INTERNATIONAL
GUARANTEE
This limited Polar international guarantee is issued by Polar Electro Inc. for
the consumers who have purchased this product in the USA or Canada. This
limited Polar international guarantee is issued by Polar Electro Oy for the
consumers who have purchased this product in other countries.
Polar Electro Inc. / Polar Electro Oy guarantees to the original consumer/
purchaser of this product that the product will be free from defects in
material or workmanship for two years from the date of purchase.
Please keep the receipt or International Guarantee Card, which is
your proof of purchase!
The guarantee does not cover the battery, damage due to misuse, abuse,
accidents or non-compliance with the precautions; improper maintenance,
commercial use, cracked or broken cases.
Guarantee does not cover any damage/s, losses, costs or expenses, direct,
indirect or incidential, consequential or special, arising out of, or related to
the product. During the guarantee period the product will be either
repaired or replaced at an authorized service center free of charge.
This guarantee does not affect the consumer’s statutory rights under
applicable national or state laws in force, or the consumer’s rights against
the dealer arising from their sales/ purchase contract.
This CE marking shows compliance of
this product with Directive 93/42/EEC.
Polar Electro Oy is a ISO 9001:2000 certified company.
Copyright © 2003 Polar Electro Oy, FIN-90440 KEMPELE, Finland.
All rights reserved. No part of this manual may be used or reproduced in any form or by any means
without prior written permission of Polar Electro Oy. The names and logos marked with a ™ symbol
in this user's manual or in the package of this product are trademarks of Polar Electro Oy. The names
and logos marked with a ® symbol in this user's manual or in the package of this product are
registered trademarks of Polar Electro Oy, except that Windows is a registered trademark of
Microsoft Corporation.
J 104
L 107
L. POLAR GLOSSARY
L 106
Activity level: Your long-term
physical activity level you need to
assess in order to do the Polar Fitness
Test.
Altitude and temperature: The
altitude and temperature are
measured by using an atmospheric
pressure sensor. Air pressure changes
constantly due to various weather
conditions and therefore the
calculated altitude of a certain spot
may differ. Variation of high and low
pressure or air conditioning can cause
a change in the altitude reading.
For example, a thunderstorm can
cause a change of up to 80 mbars,
which means a change of
approximately 700 m/ 2000 ft in the
calculated altitude. Therefore, it is
recommended that you adjust the
exact starting point altitude whenever
a reliable reference; for example, a
peak pointer or a map, is available. It
is also recommended that you check
the altitude of your house and other
common starting points for training.
Coded heart rate transmission:
Polar coded transmitter automatically
locks in a code to transmit your
heart rate to the wrist unit. In a
coded transmission the wrist unit
accepts heart rate data only from
the Polar coded transmitter. Coding
significantly reduces crosstalk
caused by other users of heart rate
monitors. However, it does not
necessarily reduce all environmental
interference.
Electrodes: The grooved areas of
the transmitter, against the skin.
Pick up the heart rate.
Maximal oxygen uptake:
(maximal aerobic power, VO
2max
) Is
the maximal rate at which oxygen
can be used by the body during
maximal work. VO
2max
is a good
index of aerobic fitness.
Maximum heart rate: (HR
max
) Is
the highest number of heart beats
per minute of a person.
Target heart rate zone: The area
between the upper and lower
target heart rate limits. Target zone
selection is based on personal
fitness goals.
ALARM: Indicates the alarm in
watch settings.
Alt.: Indicates altitude.
AM or PM: Are used in 12h Time
mode. E.g. in 24h Time mode 13:00
means 1:00 PM.
Asc.: Indicates ascended meters/
feet.
AVG: Together with a reading
indicates average heart rate.
b0: Indicates that you have no bike
settings on.
b1: Indicates bike 1 setting.
b2: Indicates bike 2 setting.
BasicUse: Exercising without
settings.
BestLap: Indicates the shortest lap
time information.
Cad*: Indicates pedaling speed
measured in rounds per minute (RPM).
Calibrate: You can return to the
previous manually set reference
point altitude.
CONNECT: Infrared
communication mode.
Cont: Up to 30 intervals succeed
one another unless the Interval
phase is manually stopped.
CoolDown: Cool-down phase at
the end of an interval training
exercise.
E0: BasicUse settings.
E1-E5: Indicates which exercise set
you have used for the exercise.
ExeSet: Start setting your BasicSet
(Int OFF) or Interval Training Set
(Int On).
Exe. Time: Exercise duration.
FILE: Indicates the file mode.
FIT. TEST: Indicates fitness test
mode.
FULL: After having stored 99 laps
(the use of intervals reduces the
amount). FULL appears in the
display. You can continue taking
lap times or intervals but they
won’t be recorded into the file.
Display texts
*Optional Polar Cadence Sensor or
Polar Power Output Sensor required.
L 109
L 108
HR
max
-p: Predicted maximum heart
rate value.
Interval, Int: Options mode:
indicates Interval Training Set
Recording mode: Indicates interval
exercise session including warm-up,
interval and cool-down phases.
InZone/ Above/ Below: indicate
the time spent within, above and
below the target zone.
KCal: Indicates the energy
expenditure of your exercise.
Lp: Indicates lap time.
LAPS: Indicates how many lap times
have been stored.
Lim High: The higher heart rate
limit of the target zone.
Lim Low: The lower heart rate limit
of the target zone.
Limits1, 2, 3: Heart Rate Limits for
Target Zones 1, 2 and 3.
Limits S: Heart Rate Limits for
Summary Zone.
LRB*: Indicates the left and right
pedaling balance.
MAX: Together with a heart rate
reading indicates the highest heart
rate.
MAX %: Together with a heart rate
reading indicates heart rate as a
percentage of your maximum heart
rate.
Mem full: Appears on the display
when the memory is full. You can
continue your exercise and taking
lap times but they won’t be
recorded into the file.
Night Mode: Appears when the
display is illuminated in the
Measuring or Recording mode.
Odometer: Measures cumulative
total distance of several exercise
sessions.
OPTIONS: Indicates the Options
mode.
OwnCal: Calculates energy
expenditure during exercise in
kilocalories. 1 kilocalorie (kcal) = 1000
calories (cal). You can follow how
much energy you loose by exercising
in one exercise session or in a day,
week or even a year. The OwnCal can
be used as a dose measure of exercise
e.g. in nutrition planning. OwnCal
calorie calculation starts when your
heart rate reaches 90 bpm or is above
60% of your maximum heart rate,
whichever is smaller. These limits are
set to count only exercise calories.
The higher the heart rate, the faster
the energy expenditure. OwnCal is
individually calibrated by your preset
weight, maximal oxygen uptake
(VO
2max
) and maximum heart rate
(HR
max
). The most accurate OwnCal is
received by entering your clinically
measured (in maximal treadmill or
bicycle stress test) VO
2max
and HR
max
into the wrist unit. Energy
expenditure measurement is most
accurate in continuous activities such
as cycling and running.
OwnINDEX: Result of Polar Fitness
Test and comparable score with
maximal oxygen uptake (VO
2max
) in
ml/kg/min.
PI %, Pedaling index*: Helps you
to analyze how evenly the power is
distributed. The smoother the
pedaling motion, the closer the
figure is to the ideal 100 %.
A pedaling index of 100 % means
that power is applied evenly
throughout the whole pedal
revolution.
Pwr*: Indicates Power Output
measurement in cycling.
RecoDist, distance-based
recovery: You set the recovery
distance in the Options mode. In the
File mode, you will see the drop in
your heart rate and the recovery
distance.
RecoHr, heart-rate-based
recovery: You set the heart rate,
which will end your recovery
calculation. In the File mode you
will see the drop in your heart rate
and the recovery duration.
RecoTime, time-based recovery:
You set the recovery time in the
Options mode. In the File mode you
*Optional Polar Cadence Sensor or
Polar Power Output Sensor required.
L 111
L 110
will see the drop in your heart rate
and the recovery duration.
Spd: Indicates velocity.
Split Time: The elapsed time from
the beginning of the exercise until
storing the split time.
Sw: Indicates stopwatch.
Timer1, 2, 3: Interval Training mode:
Countdown timers for the Interval
Training set.
WarmUp: Warm-up phase in the
beginning of an Interval Training
exercise.
Index
12h/ 24h time mode............................... 44
Activity/ button sound on/off ............... 41
Alarm settings ........................................ 43
All that you can do with your
Heart Rate Monitor ........................... 13
Altitude ...................................... 48, 54, 68
Altitude on/off ....................................... 34
Altitude reference point ....................... 34
BasicSet exercise .............................. 22, 62
Bike 1/2/OFF ............................................ 36
Buttons ...................................................... 6
Cadence on/off ....................................... 38
Care and maintenance .......................... 88
Code search ............................................ 47
Date settings ..........................................44
Deleting a file......................................... 76
Display configuration ............................ 54
Easy start ................................................... 8
Exercise set ............................................. 21
File ........................................................ 66
Fitness test .............................................. 80
Fitness test on/off .................................. 34
Frequently asked questions .................. 97
Functions during the exercise ............... 50
Guarantee ............................................. 104
Heart rate limits checking ..................... 69
Heart rate limits on/off ......................... 25
Heart rate limits settings .......................24
Heart touch function ............................. 65
Help on/off ............................................. 42
How to enter settings ............................17
HR
max
-p on/off ......................................... 34
Illuminate the display ............................ 52
Interrupt an interval
exercise phase .................................... 65
Interrupt an interval or
recovery calculation .......................... 65
Interval Training Set .............................. 22
Lap and split time storing .............. 53, 73
Measuring units settings ....................... 41
Naming bike 1 or 2 ................................ 40
Naming exercise sets.............................. 30
Odometer ...............................................71
OwnCal calorie expenditure ............... 108
OwnCal on/off ........................................ 33
OwnIndex ............................................... 80
Pause an exercise ................................... 53
Power on/off........................................... 39
Power output .................................. 55, 69
Precautions ............................................. 93
Predicted maximum heart rate............. 82
Recall training information .................. 66
Recording rate settings ......................... 31
Records file ............................................. 77
Recovery during BasicSet ............... 63, 68
Recovery during Interval training ... 60, 73
Recovery settings ............................ 26, 29
Reminder on/off ..................................... 45
Reset cumulative values ........................ 78
Reset maximum values .......................... 79
Reset the stopwatch .............................. 56
Reset the trip distance........................... 64
Return to the Time of day display ..........7
Selecting exercise type .......................... 21
Setting tips ............................................. 46
Start an exercise set ............................... 56
Start cycling measurement ................... 49
Start measuring your heart rate.... 11, 47
Stop an interval training session .......... 62
Stop measuring your heart rate .... 12, 63
Swap the exercise type .......................... 63
Swap the heart rate limits ....................52
Swap the time zones 1/ 2 ...................... 46
Technical specifications ....................... 101
Temperature.............................. 34, 54, 69
Time of day settings .............................. 44
Timer settings ......................................... 24
Transmitter ........................................ 5, 11
Update HR
max
-p and
OwnIndex to user information ........85
User information settings ..................... 18
Wheel size............................................... 37
Zone alarm On/OFF ................................ 51
L 112
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polar S725 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polar S725 in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polar S725

Polar S725 User Manual - French - 114 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info