455271
39
Zoom out
Zoom in
Previous page
1/52
Next page
39
En
Controlling the Rest of Your System
MEMO:
Some commands from other remote controls cannot
be learned, but in most cases the remotes just need to
be moved closer together or farther apart.
Certain buttons represent modes that cannot be
learned from other remote controls. These include:
RCV, CH SELECT, CH LEVEL, FUNCTION
LOUDNESS, FL DIMMER, MUTING and MASTER
VOLUME.
TV CONTROL buttons ( TV , VOL +/, and TV
FUNC ) can only be learned in TV & TVC mode.
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two
seconds.
To cancel the SETUP mode at any time
Press SETUP.
The remote control will also return to the previous
mode after thirty seconds of inactivity.
2 Press the MULTI CONTROL button for the
component you want to control
3 Press and hold the RECEIVER button for
two seconds to start the LEARNING mode.
The LED lights steadily.
To cancel LEARNING setup mode
Press SETUP for one second.
If no commands are entered within thirty seconds the
remote will revert to its previous mode.
4 Point the two remote controls towards each
other. Press the button to be learned on this
receivers remote control (for example the 3
[play] button).
Point the remote controls directly at each other, about
25 cm apart, and press the button on the remote
control for the operation you want to program. The
LED flashes rapidly.
5 Press the corresponding button on the other
remote control to be taught to this receivers
remote control (in the above example the 3
[play] button).
Point the remote controls toward each other.
Press the button on the other remote control
corresponding to the operation you wish to program.
The LED on this receivers remote will go out and
then resume a steady light if the operation is learned.
If the operation hasnt been learned for some reason
the LED will blink for three seconds and then light
steadily. If this happens press the teaching key
repeatedly, varying the distances between the
remotes, until you see the LED on this units remote
light steadily, without blinking first.
To program additional operations for the current
component
Repeat steps 4 and 5.
To program operations for another component
Repeat steps 2 through 5.
6 Press and hold SETUP for one second to exit
the LEARNING setup mode.
After thirty seconds of inactivity the remote control
will automatically leave the LEARNING mode and
revert to its previous mode.
Erasing One of the Learning
Remote Control Button Settings
This erases one of the buttons you have programmed
and restores the factory installed preset to that button.
1 Press SETUP and hold for three seconds.
The LED on the remote control will light for two
seconds.
2 Press the MULTI CONTROL button relating to
the function of the button to be cleared.
The remote control will return to the previous mode
after thirty seconds of inactivity.
3 Press the RECEIVER button twice within
three seconds to start erase mode.
The LED blinks.
4 Press the button to be cleared for three
seconds.
The LED lights steadily for three seconds and then
goes off.
5 Repeat step 4 to erase other codes.
6 Press and hold the SETUP button for one
second to exit the erase mode.
2
5 cm
TV
TVFUNC
MENU
VOLUME
MASTER VOLUME
TV CONTROL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
CHANNEL
ENTER
DISC
MPX
DISPLAY RF ATT
D.ACCESS
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP
TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
4¢
7
8
3
EFFECT
DVD VCR CD-RTV
RCV
TUN
TVC
CD
MIDNIGHT
LOUDNESS
MUTING
SETUP
FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER
SOURCE
1
2
3
4
5
6
7
8
10
9
0
2
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-D710S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-D710S in the language / languages: English as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-D710S

Pioneer VSX-D710S User Manual - English - 52 pages

Pioneer VSX-D710S User Manual - German - 52 pages

Pioneer VSX-D710S User Manual - Dutch - 108 pages

Pioneer VSX-D710S User Manual - French, Italian - 108 pages

Pioneer VSX-D710S User Manual - Portuguese, Swedish - 108 pages

Pioneer VSX-D710S User Manual - Spanish - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info