Manual Pioneer VSX-D709S (page 78 of 84) (English)

574221

Zoom out

Zoom in

1/84

Techno Tidbits & Problem-solving

Cause

• Speaker settings are incorrect.

• The rear and/or center levels are

turned down.

• The surround and/or center

speakers are disconnected.

• SIGNAL SELECT is set incorrectly.

• The digital inputs are assigned

incorrectly, or not at all.

• SIGNAL SELECT is set to

“ANALOG”.

• A DVD player not compatible with

DTS is used, or the setting of the

DVD player is incorrect.

• The digital output level has been

turned down on a CD player or

other component equipped with

digital output level adjustment

capability. (The DTS signal has been

altered by the player, and cannot be

read.)

• The speakers are turned OFF.

• Disc being played back has a huge

amount of information on it.

• The search function performed by

the player interferes with the

reading of digital information.

• The remote control batteries have

worn out.

• Too far away or bad angle of

operation.

• There is an obstacle between the

receiver and the remote control.

• Strong light such as fluorescent

light is shining onto the unit's

remote control signal light-receiving

window.

• A cord is connected to the

CONTROL IN terminal on this unit.

•The FL DIMMER button is pushed.

• If you are using an analog source,

the signal is too strong.

• If you are using a digital source,

there is too much information for

the receiver to handle.

• The SIGNAL SELECT is on

ANALOG.

Remedy

• See “Speaker Setting” on p.31-32 to

check the speaker settings.

• See “Channel Level” p.34-35 to check

the speaker levels.

• Connect the speakers (see p.19).

• Set SIGNAL SELECT to “AUTO” or

according to the type of connections

made (see p. 44).

• Set the digital input settings correctly

(see p.29).

• Make digital connections (see p.13)

and set SIGNAL SELECT to “AUTO”

(see p.44).

• Refer to the instruction manual

supplied with the DVD player.

• Set the digital volume level of the

player to full, or to the neutral

position.

• Turn the speakers ON.

• Use the STANDARD mode to get

the best results (see p.42).

• This is not a malfunction, but be sure

to turn the volume down to prevent

the output of loud noise from your

speakers.

• Replace the batteries (see p.10).

• Operate within 23 ft (7 m), 30° of the

remote sensor on the front panel (see

p.11).

• Remove the obstacle or operate from

another position.

• Avoid exposing the remote sensor on

the front panel to direct light.

• Connect cord to the correct jack.

• Press FL DIMMER on the front panel

repeatedly to return to the default

setting (see p.49).

• Press the INPUT ATT button (see

p.24).

• For 2/DTS sources put the receiver

in STANDARD mode (see p.42).

• Set the SIGNAL SELECT to DIGITAL.

Symptom

No sound from surround or

center speakers.

Sound is produced from some

components, but not from

digital components.

No sound is output or a noise is

output when software with DTS

is played back.

The sound is output

intermittently when software

with DTS is played back.

When a search is performed by

a DTS compatible CD player

during playback, noise is output.

Cannot be remote controlled.

The display is dark.

The OVER indicator is

constantly lit.

When playing a Dolby Digital /

DTS format LD there is noise

audible on the soundtrack.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-D709S in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-D709S Manual

Product: