574221
77
Zoom out
Zoom in
Previous page
1/84
Next page
77
Techno Tidbits & Problem-solving
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
Cause
The power plug is disconnected.
The protection circuit may have
been activated.
Static electricity caused by dry air.
Improper connections.
Sound is muted.
The volume is turned down.
The TAPE 2 MONITOR is ON.
Speakers are turned OFF.
DIGITAL/ANALOG switch is set
incorrectly.
The digital inputs are assigned
incorrectly, or not at all.
Improper connections.
The input source is not properly
selected.
Incorrect frequency.
The antenna is not connected.
2 RF and/or digital cables are near
the antenna terminals and wires.
FM broadcasts
The FM antenna is not fully
extended or is poorly positioned.
Weak radio signals.
AM broadcasts
The AM antenna is poorly
positioned.
Weak radio signals.
Interference caused by other
equipment (fluorescent lamp,
motor, etc.).
Weak radio signals.
Settings route signal away from
subwoofer.
The LD is not a Dolby Digital
compatible disc.
The Dolby Digital / DTS source is
not 5 channels.
Symptom
The power does not turn ON.
The unit does not respond when
the buttons are pressed.
No sound is output when a
function is selected.
No image is output when a
function is selected.
Considerable noise in radio
broadcasts.
Broadcast stations cannot be
selected automatically.
Sub woofer output is very low.
When playing an LD the SIGNAL
SELECT is on DIGITAL but there is
still no sound.
When playing a Dolby Digital / DTS
source the 5.1 Channel indicator
doesn't light.
Remedy
Connect the power plug to the wall
outlet.
Plug in again. If it still doesn't work
call a service center.
Disconnect the power plug from the
outlet, and insert again.
Make sure the component is
connected correctly (see p. 12-21).
Press MUTE on the remote control.
Adjust MASTER VOLUME.
Press the TAPE 2 MONITOR button.
Press SPEAKERS (A/B) to select the
speakers you connected.
Set SIGNAL SELECT (see p. 44).
Set the digital input settings correctly
(see p.30).
Make sure the component is
connected correctly (see p.12-21).
Press the correct function button.
Tune in the correct frequency.
Connect the antenna (see p.18).
Route 2 RF and digital cables away
from the antenna terminals and wires.
Fully extend the FM wire antenna,
position for best reception, and
secure to a wall.
Connect an outdoor FM antenna (see
p.18).
Adjust the direction and position for
best reception.
Connect an additional internal or
external AM antenna (see p.18).
Turn off the equipment causing the
noise or move it away from the
receiver.
Place the antenna farther away from
the equipment causing the noise.
Connect an outdoor antenna (see
p.18).
To get more signal to the subwoofer
set it to PLUS or choose SMALL for
the FRONT speakers (see p.31-32).
Set the SIGNAL SELECT to analog
(make sure your LD player is hooked
up with analog connections in
addition to digital and 2 RF (with RF
demodulater connections, see p. 15).
• There is no problem with the receiver
but if you want 5 channel sound you
must play a 5 channel source.
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-D709S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-D709S in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info