574068
60
Zoom out
Zoom in
Previous page
1/123
Next page
Listening to your system
06
60
En
Using the Virtual Surround Back mode
•Default setting: OFF
When you’re not using surround back speakers,
selecting this mode allows you to hear a virtual surround
back channel through your surround speakers. You can
choose to listen to sources with no surround back
channel information, or if the material sounds better in
the format (for example, 5.1) for which it was originally
encoded, you can have the receiver only apply this effect
to 6.1 encoded sources like Dolby Digital EX or DTS-ES.
1
Press
SBch
repeatedly to cycle the virtual surround
back channel options.
Each press cycles through the options as follows:
VirtualSB ON – Virtual Surround Back is always used
(for example, on 5.1 encoded material)
VirtualSB AUTO – Virtual Surround Back is
automatically applied to 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES)
VirtualSB OFF – Virtual Surround Back mode is
switched off
Setting the Up Mix function
In a 7.1-channel surround system with surround
speakers placed directly at the sides of the listening
position, the surround sound of 5.1-channel sources is
heard from the side. The Up Mix function mixes the
sound of the surround speakers with the surround back
speakers so that the surround sound is heard from
diagonally to the rear as it should be.
2
•Using the Up Mix function is effective when the
speakers in the 7.1-channel surround system are set
up as recommended in the example on page 18.
•Depending on the positions of the speakers and the
sound source, in some cases it may not be possible
to achieve good results. In this case, set the setting to
OFF.
1 Switch the receiver into standby.
2 While holding down
ENTER
on the front panel,
press
STANDBY/ON
.
The display shows RESET NO .
Use TUNE +/– (or / on the remote control) to select
UP MIX ON , and then use PRESET +/– (or / on
the remote control) to select ON or OFF.
3 Press
ENTER
to confirm.
When set to ON, the UP MIX indicator on the front
panel lights.
Note
1 • You can’t use the Virtual Surr ound Back mode when the headphones are connected to this receiver or when any of the stereo, Front Stage
Surround Advance or Stream Direct mode is selected.
You can only use the Virtual Surround Back mode if the surround speakers are on and the
SB
setting is set to
NO
or if
Front Bi-Amp
,
Speaker B
or ZONE 2 is selected at Surr Back System.
• The Virtual Surround Back mode cannot be applied to sources that do not have surround channel information.
2 • Set to ON regardless of this setting when playing DTS-HD signals.
• May automatically be set to OFF even when set to ON, depending on the input signal and listening mode.
?
C
SW
L R
SL SR
SBL SBR SBL SBR
C
SW
L R
SL SR
Up Mix OFF Up Mix ON
INPUT
SELECTOR
STANDBY/ON
PHONES
BAND
TUNE
TUNE
PHASE
CONTROL
AUTO SURR
/ALC/
STREAM DIRECT
STEREO
ADVANC
MCACC
SPEAKERS CONTROL
MULTI-ZONE
ON
/
OFF
HDMIPQLS
PRESET
PRESET
TUNER EDIT
ENTER
PUSH
OPEN
VSX-9140TXH
VSX-9140TXH_CUXJ.book 60 ページ 2009年4月16日 木曜日 午前10時36分
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-9140TXH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-9140TXH in the language / languages: English as an attachment in your email.

The manual is 11,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info