Manual Pioneer VSX-830 K (page 59 of 137) (English)

586462

Zoom out

Zoom in

1/137

Basic Setup

! MCACC – The six MCACC presets are used for storing surround sound settings for different listening posi-

tions. Simply choose an unused preset for now (you can rename it later in Data Management on page 104 ).

! Dolby Enabled Speaker (VSX-1130 only) – Select speakers that use Dolby Enabled Speaker (TMd). When

Dolby Enabled Speaker is not used, select NO (page 25 ).

! SP to ceiling (VSX-1130 only) – When using the Dolby Enabled Speaker, you can input the vertical distance

from the speaker to the ceiling (page 25 ).

! Measurement Type – When Basic is set, the minimum required measurement is performed in a short period

of time. When Expert is set, accurate and precise measurement is performed so it will take some time.

5 Select ‘START’, then press ENTER.

6 Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a

comfortable volume level.

7 Wait for the test tones to finish, then confirm the speaker configuration in the GUI screen.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present

in your setup. Try to be as quiet as possible while it’s doing this.

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,

the Full Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press

ENTER in step 7.

! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-

ing for ambient noise (see Problems when using the Auto MCACC Setup on page 59 ) and verifying the mic

connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

Now Analyzing... 2/9

Environment Check

Ambient Noise : OK

Microphone :

Speaker YES/NO :

L : YES

C : YES

R : YES

TMdR : YES

SR : YES

SBR : YES

SBL : YES

SL : YES

TMdL : YES

SW : YES

OK RETRY

Exit

2a.Full Auto MCACC

Return

Exit

2a.Full Auto MCACC

Return

The configuration shown on-screen should reflect the actual speakers you have.

! If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem

with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker con-

nections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to

change the setting and continue.

! If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the

phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are

properly connected.

If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker

connections.

— If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.

After this, perform the Full Auto MCACC procedure again.

— If the connections were right, select GO NEXT and continue.

8 Make sure ‘OK’ is selected, then press ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum

receiver settings.

Again, try to be as quiet as possible while this is happening. It may take 3 to 10 minutes.

9 The Full Auto MCACC Setup procedure is completed and the Home Menu menu reappears

automatically.

Be sure to disconnect the microphone from this receiver upon completion of the Full Auto MCACC Setup.

The settings made in the Full Auto MCACC Setup should give you excellent surround sound from your system,

but it is also possible to adjust these settings manually using The MCACC PRO (VSX-1130)/Advanced MCACC

(VSX-830) menu on page 98 or The System Setup and Other Setup menus on page 105 .

! Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12

cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual

speaker setup on page 106 .

! The subwoofer distance setting may be farther than the actual distance from the listening position. This set-

ting should be accurate (taking delay and room characteristics into account) and generally does not need to

be changed.

! If Full Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and view-

ing environment, we recommend adjusting the settings manually.

! VSX-1130 only: The Dolby Enabled Speaker distance indicates the distance of the ceiling reflection. Therefore,

it is longer than the direct distance but you do not need to change this (page 25 ).

! VSX-1130 only: When Full Auto MCACC or Auto MCACC is selected, all of the EQ adjustment values for Dolby

Enabled Speaker are set to 0 dB. You can adjust the settings manually.

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the

walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for

household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them

off if necessary. If there are any instructions showing in the front panel display, please follow them.

! Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off

the TV when doing the Auto MCACC Setup.

The Input Setup menu

You only need to make settings in the Input Setup menu if you didn’t hook up your digital equipment according

to the default settings (see Input function default and possible settings on page 60 ). In this case, you need to

tell the receiver what equipment is hooked up to which terminal so the buttons on the remote control correspond

to the components you’ve connected.

! With factory default settings, the on-screen display will be output from all HDMI output terminals and dis-

played on any TV connected via HDMI cable.

VSX-1130 only: You can change where the screen is output in the MAIN/HDZONE (page 110 ) and HDMI out-

put (page 89 ) settings.

1 Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and

then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the

screens and select menu items. Press RETURN to exit the current menu.

2 Select ‘System Setup’ from the HOME MENU.

3 Select ‘Input Setup’ from the System Setup menu.

a.Input Setup

b.HDMI Setup

c.Manual SP Setup

d.MHL Setup

e.OSD Language

f.Other Setup

Input : BD

Input Name : Rename

Audio In :

– – –

HDMI Input : – – –

Input Skip : OFF

Component In :

– – –

Exit

3.System Setup

Return

Exit

3a.Input Setup

Return

unable to get sound out of the rear speakers, can you help please Submitted on 9-4-2021 at 12:43
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-830 K in the language / languages: English as an attachment in your email.

The manual is 20,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-830 K

Pioneer VSX-830 K User Manual - German - 146 pages

Pioneer VSX-830 K User Manual - Dutch - 146 pages

Pioneer VSX-830 K User Manual - French - 145 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-830 K Manual

Product: