Manual Pioneer SC-1224 (page 96 of 126) (English)

611801

Zoom out

Zoom in

1/126

The System Setup and Other Setup menus

Important

ZONE 3 is a function for SC-2024 only. It cannot be selected or set with SC-1224.

1 Select ‘ZONE Setup’ from the Other Setup menu.

2 Select a sub zone for which you wish to change the setting.

3 Select the Volume Level setting you want.

! Variable (default) – Adjusts the sound volume of the sub zone using this unit.

! –40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set

here.

4 Select the Power ON Level setting you want.

Sets the sound volume of the sub zone when the multi-zone function is used to turn on the sub zone. Volume can

be set for ZONE 2, ZONE 3, and HDZONE, respectively.

When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot

be set here.

! LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were

listening to that zone.

! “---” – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.

! –80.0dB to 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be

set up to the value set at Volume Limit below.

5 Select the Volume Limit setting you want.

The maximum volume for the zone selected in step 2 can be set.

! OFF (default) – The maximum volume is not limited.

! –20.0dB/–10.0dB – The maximum volume is limited to the value set here.

6 Select the Mute Level setting you want.

The mute level for the zone selected in step 2 can be set.

This sets how much the volume is to be turned down when MUTE is pressed.

! FULL (default) – No sound.

! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.

7 Adjust Lch Level and Rch Level.

The channel level for the zone selected in step 2 can be set.

The level can be adjusted between –12.0dB and +12.0dB, in 1 dB steps.

8 SC-2024 only: Select the HPF (High Pass Filter) setting you want.

This can only be set when ZONE 2 is selected in step 2.

The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is con-

nected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the

AUDIO ZONE 2 OUT terminals.

! OFF (default) – The High Pass Filter function is disabled.

! ON – The High Pass Filter function is enabled.

9 Select the TONE setting you want.

This can only be set when ZONE 2 is selected in step 2.

The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such.

When ON is selected, the BASS and TREBLE can be adjusted.

! When the speaker terminals are being used for Zone 2, the TONE settings cannot be made.

10 Adjust the bass (BASS) and treble (TREBLE) to your tastes.

This can only be set when ZONE 2 is selected in step 2 and ON is selected in step 8.

The BASS and TREBLE can each be adjusted between –10.0dB and +10.0dB, in 1 dB steps.

11 When you’re finished, press RETURN.

You will return to the Other Setup menu.

On Screen Display Setup

When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over

the video output on the display. This status display can be turned off by switching this setting to OFF. The setting

can be made for the main zone and HDZONE, respectively.

! Default: ON (both the main zone and HDZONE)

1 Select ‘On Screen Display Setup’ from the Other Setup menu.

2 Select and set the main zone or HDZONE for which you wish to change the setting.

3 Select the On Screen Display setting you want.

4 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Notes

! The on-screen display is only displayed for video output from the HDMI terminal.

! When the video input signal is a 3D signal, the on-screen display may not be displayed.

! The size of the characters displayed differs according to the output resolution.

Play ZONE Setup

Select the zone for playing the audio contents of devices in the home network when using in the DMR mode.

! For playable DLNA-compatible network devices, see page 58 .

1 Select ‘Play ZONE Setup’ from the Other Setup menu.

2 Select the zone in which you want to play the audio contents.

3 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Notes

! If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off,

then play the audio contents.

! MAIN/HDZONE at ZONE Setup must be set to HDZONE in order to use the HDZONE function (page 95 ).

Maintenance Mode

Only use this if so instructed by a Pioneer service engineer or custom installer.

I have an SC 1224 receiver. I have a couple of Sonos wifi speakers. I have a mesh wifi setup in my home from my internet connection. I would like to play music from the receiver over wifi to my speakers in other parts of the house. I.e. my music is on my phone, I connect my phone to the receiver via Bluetooth, the receiver will output to the speakers wired to it in the same room, a basic setup. Now if I want to extend that music to my wireless speakers in other parts of the house too far away for Bluetooth to reach, I should be able to use my home wifi network, but how do I get the receiver to 'talk' to my home wifi network so that it can pass a signal to my wireless speakers? Submitted on 16-6-2023 at 06:39
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-1224 in the language / languages: English as an attachment in your email.

The manual is 7,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-1224

Pioneer SC-1224 Quick start guide - English, German - 76 pages

Pioneer SC-1224 User Manual - German - 133 pages

Pioneer SC-1224 Quick start guide - Dutch - 76 pages

Pioneer SC-1224 User Manual - Dutch - 130 pages

Pioneer SC-1224 Quick start guide - French - 76 pages

Pioneer SC-1224 User Manual - French - 129 pages

Pioneer SC-1224 Quick start guide - Italian, Spanish - 76 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer SC-1224 Manual

Product: