Manual Pioneer N-P01 (page 34 of 54) (English)

611810

Zoom out

Zoom in

1/54

Additional information (Network audio player: N-P01)

 A Spotify Premium account (for a charge) must be registered

on the Spotify application.

 When this unit is in standby, it cannot be selected from the

Spotify application.



The sound of the Spotify audio stream is not produced.

 Check whether this unit is selected on the Spotify application.

 Check that contents are playing on the Spotify application.

 If the above does not solve the problem, turn this unit’s power

off then back on.



This unit’s volume does not increase when the volume

slider in the Spotify application is raised.

 There is an upper limit to the volume to prevent the volume

from being too high accidentally. To raise the volume higher in

this case, do so by operating the remote control. When using

an application such as Pioneer ControlApp, the volume can

also be increased from the application.



Playback continues on this unit when the Spotify

application is quit.

 The Spotify audio stream continues from this unit, even when

the Spotify application is quit. To operate again, relaunch the

Spotify application.

Wireless LAN



Network cannot be accessed via wireless LAN.

 Is Network Type set to Auto and the LAN cable connected to

the player? Switch Network Type to Wireless or disconnect

the LAN cable from the player, then restart the player. If

Network Type is set to Auto and the LAN cable is connected

to the player, the player recognizes the Network Type as

Wired.

 This player and base receiver (wireless LAN router, etc.) are too

far apart or there is an obstacle between them. Improve the

wireless LAN environment by moving the player and base

receiver closer together, etc.

 There is a microwave oven or other device generating

electromagnetic waves near the wireless LAN environment.

Use the system in a place away from microwave ovens or

others device generating electromagnetic waves. Avoid using

devices generating electromagnetic waves as much as

possible when using the system with the wireless LAN.

 Multiple wireless devices are connected to the wireless LAN

router. When connecting multiple wireless devices, their IP

addresses must be changed.

 Wireless LAN connections cannot be established between the

player and base receiver (wireless LAN router, etc.). The player

must be set in order to establish wireless LAN connections.

See Connecting using wireless LAN on page 12.

 The IP address settings of the player does not match the

settings of the wireless LAN router, etc. Check the IP address

settings of the player (including the DHCP setting). If the

player’s DHCP setting is on, turn the player’s power off, then

turn the power back on. Check that the IP address of the player

matches the settings of the wireless LAN router, etc. If the

player’s DHCP setting is off, set an IP address matching the

network of the base receiver (wireless LAN router, etc.). For

example, if the wireless LAN router’s IP address is

“192.168.1.1”, set the player’s IP address to “192.168.1.XXX”

(*1), the subnet mask to “255.255.255.0”, the gateway and DNS

to “192.168.1.1”.

*1) Set the “XXX” in “192.168.1.XXX” to a number between 2

and 248 that is not assigned to other devices.

 The access point is set to conceal the SSID. In this case, the

SSID may not be displayed on the access point list screen. If

not, set the SSID, etc., by making the wireless LAN settings on

the player manually.

 The access point’s security settings use WEP 152-bit length

code key or shared key authentication. The player does not

support WEP 152-bit length code key or shared key

authentication.

 The SSID only supports use of single-byte alphanumeric

characters, together with the underbar and certain other

symbols. If using another character coding, the SSID must be

updated before making network settings. For more details

regarding SSID, consult your router’s operating instructions.

Setting quick start mode

Quick start mode significantly reduces the time required for

startup. It also allows the unit to power on automatically using

AirPlay, DLNA and Spotify application. Follow the steps below

to turn on quick start mode. Power consumption increases

when set to quick start mode when compared to regular

standby mode.

Press NET SERVICE, then press SETUP on the remote

control.

The Initial Setup screen is shown on the display.

Select ‘Option Setting’ from Initial Setup menu.

Select ‘Power Off Setting’ from Option Setting menu.

Select ‘Quick Start Mode’ from Power Off Setting menu.

To turn Quick Start Mode on, Use

/

to select ON,

then press ENTER.

To turn Quick Start Mode off, Use

/

to select OFF,

then press ENTER.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer N-P01 in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer N-P01

Pioneer N-P01 Quick start guide - English, German - 36 pages

Pioneer N-P01 User Manual - German - 54 pages

Pioneer N-P01 Quick start guide - Dutch - 36 pages

Pioneer N-P01 User Manual - Dutch - 54 pages

Pioneer N-P01 Quick start guide - French - 36 pages

Pioneer N-P01 User Manual - French - 54 pages

Pioneer N-P01 Quick start guide - Italian, Spanish - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer N-P01 Manual

Product: