573849
21
Zoom out
Zoom in
Previous page
1/62
Next page
Surround sound settings
07
21
En
English
Chapter 7
Surround sound settings
Using the Setup menu
From the Setup menu you can access all the surround
sound settings of the system
1
, including channel levels,
speaker distances, dynamic range adjustment and dual
mono audio playback.
Use the following buttons to use the Setup menu.
Channel level setting
The Auto MCACC feature (see page 15) should give you
the best surround sound setup. However you may find
that by further adjustment of the channel levels you can
improve the surround sound in your listening room.
This method of setting the channel levels allows you to
listen to a source and adjust the levels of each playback
channel. Note that the channel level settings for stereo
playback are independent of the settings for surround
sound playback.
A further method of setting the channel levels is to use
the test tone method. See
Adjusting the channel levels
using the test tone
on page 22 for more on this.
1 Select stereo or multichannel playback for a source.
2 Press
SETUP
.
3 Use the
/
(cursor left/right) buttons to select
CH LEVEL
, then press
ENTER
.
4 Use
/
(cursor left/right) to select a channel;
/
(cursor up/down) to adjust the level of that channel.
You can adjust the level of each channel by ±10 dB.
If the system is in Stereo or Virtual mode, or a stereo
source is playing in Auto mode, you will not be able
to adjust the center or surround channels.
5 Press
ENTER
when you’re finished.
If you use the Auto MCACC feature again, it will
overwrite the settings you have made here.
Speaker distance setting
The Auto MCACC feature (see page 15) should give you
the best surround sound setup. However you may find
that by further adjustment of the speaker distance
settings you can improve the surround sound in your
listening room.
Set the distance of each speaker from your normal
listening position.
1 Press
SETUP
.
2 Use the
/
(cursor left/right) buttons to select
DISTANCE, then press
ENTER
.
3 Use
/
(cursor left/right) to select a speaker;
/
(cursor up/down) to adjust the distance.
Adjust the following speakers:
L
– Front left speaker
C
– Center speaker
R
– Front right speaker
SR
– Surround right speaker
SL
– Surround left speaker
SW
– Subwoofer
Each speaker can be adjusted from
0.3 m
to
9.0 m
.
4 Press
ENTER
when you’re finished.
If you use the Auto MCACC feature again, it will
overwrite the settings you have made here.
Dynamic Range Control
When watching Dolby Digital or DTS material at low
volume, low level sounds — including some of the
dialogue — can be difficult to hear properly. Using one of
the Dynamic Range Control (DRC) settings can help by
bringing up the low level sounds, while controlling high
level peaks.
Dynamic Range Control works only with Dolby Digital
soundtracks and some DTS soundtracks.
1 Press
SETUP
.
2 Use the
/
(cursor left/right) buttons to select
DRC, then press
ENTER
.
Note
1 There are other settings you can adjust from the Setup menu; these are explained in
Listening to the radio
on page 19 and
Additional
information
on page 26.
ST
TUNE
TUNE
ST
ENTER
ENTER
CLEAR
SOUND
SETUP
TEST
TONE
SOUND
RETRIEVER
MCACCADVANCED F.S.SURRSURROUND
SLEEP
SR
ST
TUNE
TUNE
ST
ENTER
SETUP
HTP-330.book 21 ページ 2007年3月27日 火曜日 午後6時8分
Downloaded from www.Manualslib.com manuals search engine
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer HTP-330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer HTP-330 in the language / languages: English as an attachment in your email.

The manual is 3,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info