Manual Pioneer GM-3100T (page 3 of 8) (English, French)

60549

Zoom out

Zoom in

1/8

Connecting the Unit

Using the Speaker Input

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input connector.

• Do not connect both the RCA input and the

speaker input at the same time.

7 Connections when using the speaker

input

Connecting the Speaker Wires

The speaker output mode can be two-chan-

nel (stereo) or one-channel (mono).

Connect the speaker leads to suit the mode

according to the figures shown below.

• Do not connect both the RCA input and the

speaker input at the same time.

Two-channel mode (stereo)

One-channel mode (mono)

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tapping

screws (4 × 18 mm) into the screw

holes. Push on the screws with a

screwdriver so they make marks

where the installation holes are to be

located.

2. Drill 2.5 mm (1/8 inch) diameter

holes at the point marked, and

install the amplifier, either on the

carpet or directly to the chassis.

(Left)

Speaker

(Right)

Speaker (Mono)

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ...................................................................................................... 15.0 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 4.0 A (4 Ω for two channels)

7.8 A (4 Ω for one channel)

Fuse .......................................................................................................................................................................... 25 A × 1

Dimensions ........................................................................................................................ 300 (W) × 60 (H) × 186 (D) mm

[12 (W) × 2-3/8 (H) × 7-3/8 (D) in.]

Weight ........................................................................................................ 2.7 kg (6.0 lbs.) (Leads for wiring not included)

Maximum power output .............................................................................................. 120 W × 2 ( 4 Ω) / 300 W × 1 ( 4 Ω)

Continuous power output .......................................................... 60 W × 2 (at 14.4 V, 4 Ω, 20 Hz — 20 kHz 0.08% THD)

150 W × 1 (at 14.4 V, 4 Ω, 20 Hz — 20 kHz 0.8% THD)

75 W × 2 (at 14.4 V, 2 Ω, 20 Hz — 20 kHz 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

(Bridge connection: 4 — 8 Ω allowable)

Frequency response .......................................................................................................... 10 Hz — 50 kHz (+0 dB, –1 dB)

Signal-to-noise ratio ...................................................................................................................... 100 dB (IEC-A network)

Distortion .......................................................................................................................................... 0.008 % (10 W, 1 kHz)

Separation ........................................................................................................................................................ 70 dB (1 kHz)

Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

Gain control ...................................................................................................................................... RCA: 200 mV — 6.5 V

Speaker: 0.8 — 26 V

Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 kΩ

Speaker: 26 V / 40 kΩ

Power output ........................................................................................ 60 W RMS × 2 channels

(4 Ω and 1 % THD+N)

150 W RMS × 1 channel

(4 Ω and 1 % THD+N)

75 W RMS × 2 channels

(2 Ω and 1 % THD+N)

Signal-to-noise ratio ............................................................ 80 dBA (Reference: 1 W into 4 Ω)

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

Speaker output

Car Stereo

Speaker input connector

To speaker input terminal of

this unit.

White:

Left

Gray:

Right +

White/black:

Left ≠

Gray/black:

Right ≠

Drill a 2.5 mm (1/8 inch)

diameter hole

Tapping-screws

(4 × 18 mm)

Floor mat

or chassis

Specifications

Installation <ENGLISH>

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer GM-3100T in the language / languages: English, French as an attachment in your email.

The manual is 0,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer GM-3100T Manual

Product: