572157
45
Zoom out
Zoom in
Previous page
1/48
Next page
9 Additional Information
45
Symptom
Playback sound is
muddy or distorted;
high frequency sounds
are excessively
emphasized.
Timer doesn’t operate.
Remote control unit
doesn’t work.
Power won’t turn on to
the deck or CD receiver.
Remote Locator
function doesn’t work
Likely cause
The Dolby NR setting is not the same as that
used during recording.
Clock isn’t set to the correct current time.
Power interruption has caused the clock to be set
to the incorrect time (when the clock display is
flashing).
Batteries are exhausted.
A fluorescent lamp is located close to the remote
control unit.
The remote control unit is not pointed at the
signal receiver on the display unit.
System cable connection is incorrect.
The microphone in the remote control is covered
The remote control is too far away.
The battery in the remote control is dead.
The slide switch is in the OFF position.
The interval between claps is too long or too
short.
Remedy
Set the Dolby NR system to the same setting as
that used during recording (see p.22).
Reset the clock to the correct current time
(see p.16).
Reset the clock to the correct current time
(see p.16).
Load new batteries.
Remove the fluorescent lamp from the area of
the remote control unit.
Point the remote control unit at the remote
sensor (located on the right side of the display
unit) when operating.
Connect the system cable correctly.
This is not a malfunction.
Move to a different location and try again.
Replace the battery.
Slide the Remote Locator switch to the ON
position
The interval should be about a second.
When the system is installed near a television set, magnetic influence from the speakers may cause the television’s picture to be
distorted. This symptom frequently occurs when using an indoor antenna; in this event, install an outdoor antenna, or separate
the system farther from the television.
Static electricity and other outside electrical influences may cause the system to operate incorrectly. In such cases, unplugging
and reconnecting the power cord may help correct the problem.
More than one of the same kind of component (CD receiver, MD recorder, or cassette deck) cannot be connected at the same
time.
NOTE
Setting the tuner’s frequency interval:
FM broadcasts are normally tuned at 50kHz intervals and AM broadcasts at 9kHz intervals, but this setting can be changed to
100kHz (FM) and 10kHz (AM) if desired in the following way:
1. Switch the unit into standby mode.
2. Press
MENU and choose TUNER F. STEP using the $ or button. Press SET to select it.
3. Switch between
AM 9K (FM 50K) and AM 10 K (FM 100 K) using the $ and buttons. Press SET to select.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer CT-L77 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer CT-L77 in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info