625516
155
Zoom out
Zoom in
Previous page
1/204
Next page
CAUTION
! Thoroughly check the conditions before per-
forming Auto EQ, as the speakers may be da-
maged if this is performed under the following
conditions:
When the speakers are incorrectly con-
nected. (For example, when a rear speaker
is connected as a subwoofer output.)
When a speaker is connected to a power
amp delivering output higher than the
speakers maximum input power capabil-
ity.
! If a microphone for acoustical measurement
(sold separately) is not placed in an appropri-
ate location, the measurement tone may be-
come loud and measurement may take a long
time, resulting in battery drainage. Be sure to
place the microphone in the specified loca-
tion.
Before operating the Auto EQ
function
! Perform Auto EQ in as quiet a place as pos-
sible, with the vehicle engine and air condi-
tioning switched off. Also, cut power to car
phones or cellular phones in the vehicle, or
remove them from the vehicle before per-
forming Auto EQ. Sounds other than the
measurement tone (surrounding sounds,
engine sound, telephones ringing, etc.)
may prevent correct measurement of the
vehicles acoustics.
! Be sure to perform Auto EQ using the mi-
crophone for acoustical measurement
(sold separately). Using another micro-
phone may prevent measurement, or result
in incorrect measurement of the vehicles
acoustics.
! To perform Auto EQ, the front speakers
must be connected.
! When this navigation system is connected
to a power amp with input level control,
Auto EQ may be impossible if the power
amps input level is set below the standard
level.
! When this navigation system is connected
to a power amp with an LPF (low pass fil-
ter), turn the LPF off before performing
Auto EQ. Also, set the cut-off frequency for
the built-in LPF of an active subwoofer to
the highest frequency.
! The distance has been calculated by com-
puter to provide optimum delay to ensure
accurate results. Do not change this value.
The reflected sound within the vehicle is
strong and delays occur.
The LPF on active subwoofers or exter-
nal amps delay the lower sounds.
! If an error occurs during measurement, a
message appears and measurement is
canceled. Check the following before mea-
suring the vehicles acoustics.
Front speakers (left/right)
Rear speakers (left/right)
Noise
Microphone for acoustical measure-
ment (sold separately)
Low battery
Performing Auto EQ
p Auto EQ changes the audio settings as fol-
lows:
! Auto EQ on the EQ Menu screen is
set to On.
= For details, refer to Using the auto-ad-
justed equalizer on page 153.
! The fader/balance settings return to the
center position.
= For details, refer to Using balance ad-
justment on page 150.
! The equalizer curve switches to Flat.
= For details, refer to Using the equali-
zer on page 151.
! The front and rear speakers will automa-
tically be adjusted to a high pass filter
setting.
p Previous settings for Auto EQ will be over-
written.
p For AVIC-Z150BH users
En
155
Chapter
27
Customizing preferences
Customizing preferences
155


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-X850BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-X850BT in the language / languages: English as an attachment in your email.

The manual is 10,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info