651675
7
Zoom out
Zoom in
Previous page
1/116
Next page
Connecting up 02
7
En
English
DeutschFrançais
Nederlands
Italiano Español Русский
Digital audio input connections
If you connect the DIGITAL IN terminal of the unit and
the digital audio output of a digital audio device with a
separately sold digital cable, you can play the audio of
the digital audio device with the unit.
For details on the output of audio input to the DIGITAL
IN terminal, refer to page 11.
Note
Digital signal formats that can be input to this unit
include linear PCM signals with sampling rate and
quantitative bits up to 192 kHz/32 bits. (Depending
on the connected device and environment,
operation may not be successful).
Using a USB cable to connect to a
computer
If a USB cable (sold separately) is used to connect this
unit’s DIGITAL IN USB terminal to a computer’s USB
port, music files located on the computer can be played
through this unit.
For more information regarding the output of audio
signals input to the DIGITAL IN USB terminal, consult
page 13.
Important
A dedicated driver needs to be installed on your
computer (page 13).
Note
This unit cannot be used to play audio files from a
computer unless Media Player is installed on the
connected computer.
LINE2
LINE2
LINE1
LINE1
USB
USB
COAXIAL
COAXIAL
DIGITAL IN
DIGITAL IN
G
IN
ANALOG IN
OPTICAL
OPTICAL
LINE2
LINE2
OUT
OUT
C
ED IN
BALANCED IN
NORMAL
NORMAL
INVERSION
INVERSION
PHASE
PHASE
DIGITAL OUT
COAXIAL
DIGITAL OUT
OPTICAL
Digital audio
equipment, etc.
Coaxial digital audio cable
(sold separately)
A-70DA’s rear panel
Optical digital audio cable
(sold separately)
Digital audio
equipment, etc.
LINE2LINE2
LINE1LINE1
USBUSB
COAXIALCOAXIAL
DIGITAL INDIGITAL IN
G INANALOG IN
OPTICALOPTICAL
LINE2LINE2
OUT OUT
CED INBALANCED IN
NORMALNORMAL
INVERSIONINVERSION
PHASEPHASE
USB
USB cable
(sold separately)
A-type
B-type
PC
A-70DA’s rear panel
Using centralized control with other
Pioneer components
Multiple Pioneer components equipped with CONTROL
IN/OUT jacks can be connected to the unit, allowing
centralized control of the components via the remote
sensor on the unit. This also allows remote control of
components not equipped with a remote sensor, or
installed in places where the component’s remote
sensor cannot be accessed.
Note
For connections use a commercially available
monaural miniplug cord (without resistor).
When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
When a control cord is connected to the unit’s
CONTROL IN jack, the unit cannot be controlled by
pointing the remote control at the unit (the remote
sensor is automatically disabled).
Plugging in
Important
When going on a trip or otherwise not using the
unit for an extended period, always disconnect the
power cord from its outlet. Note that various
internal settings will not be lost even if the power
cord is disconnected from its outlet for an extended
time.
If it is necessary to detach the power cord, first be
sure to press the
/I
STANDBY/ON button on the
front panel of the unit so the unit is turned OFF
before detaching the cord.
Caution
The use of a power cord other than the one provided
will invalidate the warranty, since Pioneer will not
be responsible for any damage incurred. (The
power cord provided with the unit has a rated
current capacity of 10 A.)
Do not use any power cord other than the one
supplied with this unit.
Do not use the supplied power cord for any purpose
other than that described below.
After you’ve finished making all connections, plug the
unit into an AC outlet.
1 Plug the supplied power cord into the
AC IN
socket on the rear panel of the unit.
2 Plug the other end into an AC outlet.
IN
OUT
CONTROL
Other Pioneer
component equipped
with CONTROL IN/
OUT jacks
To other Pioneer
component
equipped with
CONTROL IN jack
A-70DA
Aim remote control
at the sensor on the
unit.
Remote
control
To AC outlet
This unit’s rear panel
Power cord
(included)
A70_SYXE8_0728.book 7 ページ 2015年7月28日 火曜日 午後3時54分
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer A-50DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer A-50DA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 23,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info