651675
6
Zoom out
Zoom in
Previous page
1/116
Next page
02 Connecting up
6
En
When using speakers with removable network
circuits, note that if the network is removed, no
effect will be produced and damage may be caused
to the speaker.
Another method of connection is to connect the
SPEAKERS A terminals to HIGH and the SPEAKERS
B terminals to LOW (reverse that shown in the
illustration).
Connecting speaker cables
1 Twist the cable cores.
2 Loosen the nut on the
SPEAKERS
terminal, and insert the speaker cable into
the exposed hole in the terminal shaft.
3 Retighten the terminal nut.
Caution
When using only one set of speaker terminals
(SPEAKERS A or SPEAKERS B), or when utilizing
bi-wiring connections, the speaker used should
have a nominal impedance between 4 and
16 . When using both sets of terminals, the
connected speakers should have nominal
impedance between 8 and 32 . Consult the
instructions accompanying your speakers for
details regarding the impedance value.
Make sure the positive and negative (+/–) terminals
on the amplifier match those on the speakers.
These speaker terminals carry HAZARDOUS live
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the
back panel it may cause the power to cut off as a
safety measure.
Connecting audio cables
Connect the white plug to the left (L) jack, and the red
plug to the right (R) jack. Be sure to insert the plugs fully
into the jacks.
123
10 mm
Left (white)
Right (red)Right (red)
Connecting to the balanced input
terminals (A-70DA only)
Connect the BALANCED IN terminals of the unit to a
SACD player, USB DAC, network player, or other device
with balanced output terminals.
Caution
•The BASS, TREBLE, BALANCE, and LOUDNESS
functions do not work for a device connected to the
BALANCED IN terminals.
The phase may differ depending on the device to be
connected. Use the phase selector switch on the rear
panel of the unit to match the phase.
Initial setting (No. 2 HOT)
Settings when polarity changed
(No. 3 HOT)
Note
For details on the phase of the balanced output
terminals of the device to be connected, refer to the
instruction manual of the device.
When connecting the unit to a Pioneer player,
match the phase to the initial setting (No. 2 HOT).
LINE2
LINE2
LINE1
LINE1
USB
USB
COAXIAL
COAXIAL
PHONO
(MM/MC)
SIGNAL
GND
NETWORK
NETWORK
SACD/CD
SACD/CD
DIGITAL IN
DIGITAL IN
ANALOG IN
ANALOG IN
OPTICAL
OPTICAL
LINE2
LINE2
OUT
OUT
P.
P.
AMP
AMP
DIRECT
DIRECT
BALANCED IN
BALANCED IN
NORMAL
NORMAL
INVERSION
INVERSION
PHASE
PHASE
RL
Audio device with
balanced output terminals
Balanced cable
(sold separately)
Balanced cable
(sold separately)
A-70DA’s rear panel
NORMALNORMAL
INVERSIONINVERSION
PHASEPHASE
1 Ground
3 COLD (-)
2 HOT (+)
NORMAL
NORMAL
INVERSION
INVERSION
PHASE
PHASE
1 Ground
3 HOT (+)
2 COLD (-)
A70_SYXE8_0728.book 6 ページ 2015年7月28日 火曜日 午後3時54分
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer A-50DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer A-50DA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 23,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info