748304
4
Zoom out
Zoom in
Previous page
1/11
Next page
2.4 Menu navigation
The primary control for moving through menus and options is the Select
Control. Rotate the control to move up or down a menu. Once the required
option or value is highlighted, press the Select Control. All menus and lists
act as loops such that turning the control to go beyond the first or last entry in
a menu or list takes you to the opposite end of the menu or list. So going up
from the first entry in a menu will take you to the last option in the menu, etc.
A “>” appears on the right of the screen if there are more options above
or below those visible.
To enter the menu tree in a particular mode press Menu. To move back a
menu level press Back. To exit the menu system, press Menu again. Each
mode has a Mode menu, with options specific to that mode.
For example, the FM mode menu has two mode specific options:
Scan setting and Audio setting.
In addition, each mode menu has a final option:
System settings >. The ‘>’ indicates options leading to further menus.
The System settings menu presents system setting functions to allow the
user to setup how the unit behaves. This includes Equalizer, Sleep, Alarms,
Streaming Audio quality, network, time/date, language, factory reset,
software update, Setup wizard, info, Privacy policy and backlight.
3. Started and setup
When IR1 is started for the first time, it runs through a setup wizard to
configure settings for date/time and network. Once this has finished,
the system is ready to use in most modes.
Note: To change these settings later, select Menu >System settings >
and select the required settings option(s).
To run the setup wizard again, select Menu > System settings > Setup wizard.
7
The Network settings can be reset later manually running the Network
wizard, select Menu > System settings > Network wizard .
Select Yes to start the setup wizard.
If you choose No, a second screen asks if you would like to run the
wizard next time IR1 is started;
select Yes or No. The system then starts without configuring time/date
and network settings and enters the Main Menu.
Note: If power is removed while the wizard is in progress, the wizard will
run again next time IR1 is started.
3.1 .1 12/24 hour display
To change between 12 and 24 hour display, select Time/Date > Set format
12/24 hour format and then select your preference.
3.1.2 Set Time/Date (wizard)
The date and time are displayed as dd-mm-yyyy and hh:mm with the first
value, dd, active (flashing). Adjust each value with the Select control. As
each value is set by pressing the Select control, the next value becomes
active ready for adjustment.
Auto-update
Auto-update works with data sent over DAB, FM or network. The clock is only
updated when in a corresponding mode, so it is best to select a mode
you use regularly.
DAB and FM use time signals broadcast with radio transmissions.
Network uses a time signal sent from the Internet radio portal when in
any network-connected mode.
1. Select Update from DAB, Update from FM, Update from Network or
No update.
2. If you are updating from the network, set your time zone.
3. If your country uses daylight saving, the automatically updated time from
the network may be wrong by one hour. When daylight savings are in effect
(during the winter), turn on the Daylight savings option to rectify this.
8
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pinell Supersound 101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pinell Supersound 101 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pinell Supersound 101

Pinell Supersound 101 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info