643476
48
Zoom out
Zoom in
Previous page
1/64
Next page
The pellet stove with Multifuoco System’ is tted with one/two fans for the circulation of hot air according to the model.
This system allows several solutions for the distribution of ducted hot air, so that the user has freedom of choice as regards the number of adjoining
rooms which can be heated.
Operation of the Multifuoco System’ will be explained in general and conceptual terms below.
In order to adjust the fan to suit the chosen ducting solution, four ‘Multifuoco System’ speed settings have been pre-programmed, which appear
as 01, 02, 03, 04 in the bottom line of the display and as small rectangles from 1 to 4 in the top line.
There is a greater volume of air transferred by the fan passing from speed setting 01 to 04.
Once the ‘Multifuoco System’ speed has been set, the user can choose a higher or lower amount of heat by selecting one of the ve power settings
on the stove: P1, , P5.
Similarly, there is a greater quantity of hot air produced by the stove passing from power setting P1 to P5.
It is at the user’s discretion, based upon experience and familiarity in using the product, which of the ‘Multifuoco’ speed settings and which power
level to choose.
These choices will be based on the length of the ducting and the required room temperature (as an indication, the longer the ducting the higher the
Multifuoco System speed setting).
For each of the solutions described in the INSTALLATION section under MULTIFUOCO SYSTEM”, there is a specic Multifuoco fan setting
recommended.
If opting for SOLUTION 1, it is best to use the control panel to select the speed setting “01”.
If opting for SOLUTION 2, a higher fan speed will be required, in which case for the fan connected to the long duct the speed setting on the control
panel shall not be lower than 02”.
Finally, if opting for SOLUTION 3 or SOLUTION 4, an even higher fan speed will be required, in which case it would be best to select the speed setting
03 or “04 on the control panel.
To select the required Multifuoco setting, refer to the paragraph “NORMAL OPERATION”.
SELECT UNIT
Function Action Display
Select UNIT function
Open the ap and press the SET and OPT keys simultaneously. Using the
SELECT MENU key choose one of the eight transmission units (0 - 8).
Standard setting on pellet stoves is 0.
SELECT
UN IT 2
SEARCH
FIELD
UN IT 2
L OADED
1
Restart stove
Disconnect the power cable. Reconnect it and within ve seconds press
the ON/OFF key, keeping it pressed down for approx. 3 - 4 seconds.
An audible beep indicates the successful change of unit.
Two display pages will appear in sequence while the remote control will
return to the initial display.
SELECT
UN IT 2
SEARCH
FIELD
UN IT 2
L OADED
1
SELECT
UN IT 2
SEARCH
FIELD
UN IT 2
L OADED
1
a Unit storage remains as set even without batteries.
DT2040072-05
DT2010248-04
6.17 MOdIFyING ThE TRANSMISSION UNIT
Should two pellet stoves of the same model be installed close to each other and the remote control beam activates both simultaneously, it is possible
to modify the transmission unit when the stove has been shut down by taking the following steps:
DT2010231-04
6.18 ‘MULTIFUOCO’ SySTEM OPERATION
H07028100/DT2000970 – 01
48
English
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Piazzetta P960 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Piazzetta P960 in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info