698650
8
Zoom out
Zoom in
Previous page
1/28
Next page
8
9
PROGRAMMAZIONE • PROGRAMMING
PROGRAMMATION • PROGRAMMIERUNG
PROGRAMMAZIONE SENSORI
I sensori possono essere programmati direttamente dal display.
1 Rimuovere il display dal supporto.
2 Premere i tasti
per posizionarsi sul pneumatico che si vuole programmare.
3 Posizionare il display vicino al sensore (tra i 10 e i 30 cm) e premere il tasto SET
per almeno 2 secondi. L’icona LF comparirà sul display per confermare la programmazione.
4 Entro 2 secondi, ad avvenuta programmazione, il display emetterà 2 beeps. Il pneumatico
corrispondente smetterà di lampeggiare e pressione e temperatura verranno visualizzate sul
display. Se entro 10 secondi il sensore non viene riconosciuto il display emetterà un breve
beep. In questo caso sarà necessario ripetere la programmazione.
5 Eseguire le stesse operazioni per tutti i pneumatici da programmare.
6 Al termine di tutta la programmazione ricollegare il display sul supporto.
NOTE: I sensori della confezione sono tutti pre-programmati di fabbrica. Seguire la posizione corretta dello schema.
In caso di errata programmazione ripetere la procedura.
SENSOR PROGRAMMING
Sensors can be programmed directly from the display.
1 Remove the display from the holder.
2 Press keys
per posizionarsi sul pneumatico che si vuole programmare.
3 Posizionare il dispto position on the tire that needs to be programmed.
3 Place the display near to the sensor (at about 10-30 cm). Keep the SET-key pressed for at least 2
seconds. The icon LF appearing on the display conrms that programming has been completed.
4 Within 2 seconds after the eected programming, the display will emit 2 beeps.
The corresponding tire stops blinking. Pressure and temperature will appear on the display. If the
sensor is not recognised within 10 seconds, the display will emit one brief Beep. In such case the
programming has to be repeated.
5 Repeat the same operations for all tires which have to be programmed.
6 Reconnect the display to the holder, as soon as programming is nished.
NOTES: The sensors supplied in the package are all Factory-preprogrammed. Please follow the correct position indi-
cated on the scheme. Repeat the procedure in case of wrong programming.
PROGRAMMATION DES SENSEURS
Les senseurs peuvent être programmés directement à partir de l’acheur.
1 Enlever l’acheur du support.
2 Appuyer sur les touches
pour se placer sur le pneu à programmer.
3 Positionner l’acheur à côté du senseur (entre 10 et 30 cm) et appuyer la touche SET
pendant au moins 2 secondes. Licône LF apparaitra sur l’acheur pour valider la programma-
tion.
4 Dans les 2 secondes suivant la programmation, l’acheur fera 2 beeps. le pneu concerné
arrêtera de clignoter et la pression et température seront visibles sur l’acheur. Si dans les 10
secondes le senseur nest pas reconnu, l’acheur fera un bref beep; dans ce cas il sera nécessaire
répéter la programmation.
5 Faire la même opération pour tous les pneus à programmer.
6 A la n de toute la programmation, rebrancher l’acheur sur le support.
NOTE: Les senseurs dans l’emballage sont tous préréglés d’origine. Suivre la position correcte du schéma. En cas de
programmation erronée, répéter la procédure.
IT GB
FR D
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phonocar VM363 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phonocar VM363 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info