Manual Philips VR1100 (page 23 of 39) (English)

462271

Zoom out

Zoom in

1/39

— 24 —

Notes:

• The DSPC system works for both SP and

LP modes only after a tape has been inserted

and the Record mode is first initiated. It does

not work during recording.

• The DSPC system does not work while

Auto Satellite Prog recording is in

progress (✈ P. 28).

• In the case of timer recording, the DSPC

system works before recording is initiated.

• Once the cassette is ejected, the DSPC data

is cancelled. The next time the cassette is

used for recording, DSPC is re-performed.

• While “DSPC” is displayed, the VCR

does not start One Touch Recording (✈P.

26).

• Since the DSPC system works before

recording actually starts, there is a delay

of approximately 7 seconds after REC/

OTR ¶ is pressed. To make sure you

record the desired scene or programme in

its entirety, first perform the following

steps:

1) Press and hold PAUSE/STILL

on the

front panel and press REC/OTR

the front panel to engage the RECORD

PAUSE mode.

• The VCR then automatically checks the

condition of the tape and, after

approximately 7 seconds, re-enters

RECORD PAUSE.

2) Press REC/OTR

to start recording.

• If you want to bypass the DSPC system

and begin recording immediately, set

“DSPC” to “OFF”.

For Playback

Press PLAY 3.

• The VCR adjusts the playback picture

quality based on the quality of the tape in

use.

• DSPC is active during Auto Tracking.

“DSPC” appears blinking on the front

panel’s display window.

Notes:

• When watching a tape recorded with

“DSPC” set to “ON”, it is recommended

that you leave DSPC to “ON” during

playback as well.

•“DSPC” only appears at the beginning of

automatic tracking. Even though it doesn't

appear after that, the DSPC function is

operative.

DVANCED

PERATIONS

(CONTINUED)

DSPC

The DSPC (Digital Studio Picture

Control) system checks the condition

of the tape in use during recording and

playback, and compensates to provide

the highest possible recording and

playback pictures. The default setting

for both recording and playback is

“ON”.

1Select VCR Set Up Screen

1 Press VCR.

2 Press MENU.

3 Press 5 or ∞ to select “VCR SET

UP” then press OK/STATUS.

2Set DSPC Mode

Press 5 or ∞ to select “DSPC”, then

press 3 to set to “ON” or “OFF”.

3Finish Setting

Press MENU.

Once the “DSPC” mode is set to “ON”,

the DSPC system works for both

recording & playback, as described

below;

For Recording

Press REC/OTR ¶.

• The VCR spends approximately 7 seconds

assessing the condition of the tape, then

begins recording.

SmartPicture

You can make the picture softer or

sharper or distinct the picture when

playing the tape.

SmartPicture is set to AUTO when you

receive the VCR.

1Select SmartPicture Mode

1 Press the

SMARTPICTURE

button. The

current setting will

appear on the

screen for about 5 seconds.

2 While the current setting appears,

press the SMARTPICTURE button

repeatedly, the setting changes as

follows.

AUTO:

Normally select this mode.

DISTINCT:

Select this mode when you want

the distinct picture. The picture

detail is emphasized.

SOFT:

Select this mode when you want

the soft picture. The signal noise of

the picture is softened.

SHARP:

Select this mode when you want

the sharp picture. The picture edge

is emphasized.

Notes:

• It is recommended that the SmartPicture

is set to “SOFT” if playback picture is

noisy.

• When “DSPC” is set to “OFF”,

“AUTO” is switched to “NATURAL”

automatically.

DURING DSPC

DSPC COMPLETED

AUTO

\DSPC ON

O. S. D. ON

DIRECT REC ON

AUTO SP=LP TIMER OFF

DIGITAL 3R ON

POWER SAVE OFF

AUTO SAT

RECORD LINK OFF

SELECT : 5∞ CHANGE :4

END : MENU

Untitled-2 16/08/2000, 15:3824

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Philips VR1100 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Philips VR1100 Manual

Product: