54447
30
Zoom out
Zoom in
Previous page
1/39
Next page
31
Useful function for Timer
Recording: Auto Tape Speed
With this function activated, the VCR can
change the tape speed and record the
programme in LP mode if not enough
tape remains for recording in SP mode.
1 Press VCR.
2 Press MENU.
3 Press 5 or to select VCR SET
UP, then press OK/STATUS.
4 Press 5 or to select AUTO SP =
LP TIMER.
5 Press 4.
Each time you press the button, the
setting changes.
ON:
Select this to allow the VCR to
change the tape speed from SP to
LP when there is not enough tape
length remaining.
OFF:
Select this not to allow the VCR to
change the tape speed.
6 Press MENU to exit from the menu
operations.
Notes:
The Auto SP
=
LP Timer feature is not
available during OTR (One Touch
Recording) and the feature will not work
properly with any tapes longer than E-
180 or with some tapes of shorter lengths.
If you have programmed the recorder to
timer-record 2 or more programmes, the
second programme and those hereafter
may not fit on the tape if you set AUTO
SP
=
LP TIMER to ON. In this case,
make sure the mode is not engaged, then
set the tape speed manually during timer
programming.
In order to ensure that the recording fits on
the tape, this feature may leave a short non-
recorded section at the end of the tape.
There may be some picture noise and sound
disturbance at the point on the tape where
the recorder switches from SP to LP mode.
If you perform timer recording with both
VPS/PDC and the Auto SP
=
LP Timer
activated, and the programme goes
beyond its originally scheduled length,
there may be times when the programme
cannot be recorded in its entirety.
When two programme overlap
The Program
Review
screen will
appear with
a magenta
line blink-
ing on the
newly set
timer recor-
ding, while the other overlapped
programme blinking.
1 Press 5 or to move
the mage-
nta line
among the
two over-
lapping
programs.
2 Press OK/
STATUS
to view
the detail information of the
program you want
to change.
3 Go to step 4 through 9 on page 30 for
Timer Recording to modify the
selected program. To cancel any
timer recording, press CLEAR.
If you do not modify the overlapping
programs, the VCR will record the earlier
program completely. Only the remaining
part of the later program will be recorded.
If the START time for the two programs
are the same, the lower program number
will be recorded.
ONE TIME PROGRAM
PROGRAM 1
TV PROG +/- 12
START+/- 08:00
STOP +/- 10:00
REC SPEED SP
VPS/PDC ON
DATE +/- 21/07/00
FRIDAY
ERASE : CLEAR
CONFIRM : OK END : TIMER
PR CH START STOP DATE
1 12 08:00 10:00 21/07
2 25 11:00 13:00 10/08
3 03 09:00 11:00W14/07
4 45 03:00 03:15W15/10
5
6
7
8
SELECT : 5∞
CONFIRM : OK
Turbo Timer
This function allows you to set the
timer recording program without going
through the regular set up with the on
screen. The extent of programming is
24 hours from the current time.
1 Insert a tape into the VCR and press
the TURBO TIMER button on the
remote control. Current time will
appear on the display panel.
2 To change the START time, press the
5 or ( if you press and hold the
button, the time changes in
30-minute increments) then press
OK/STATUS.
3 To change the STOP time, press the
5 or ( if you press and hold a
button, the time changes in
30-minute increments) then press
OK/STATUS.
4 To change the CHANNEL position,
press the 5 or , then press
OK/STATUS.
5 The data input will be memorized
and the Turbo Timer mode will be
finished so that normal display
appears.
6 Turn off the VCR.
Notes:
To exit Turbo Timer mode at any step,
press the TURBO TIMER button.
If Err appears on the display panel,
all eight programs have been set and
Turbo Timer will not proceed. To
remove the error message, press the
TURBO TIMER button again.
Settings of Turbo Timer will appear
on the display panel only and not on
the screen.
Programs Overlap Warning does not
function with Turbo Timer.
DAILY or WEEKLY programming
are not available on Turbo Timer.
Tape speed can be selected anytime
during steps 2 through 4.
SP
VCR
SP
VCR
SP
VCR
SP
VCR
Untitled-2 16/08/2000, 15:3831
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips VR110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips VR110 in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips VR110

Philips VR110 User Manual - German - 39 pages

Philips VR110 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info