368271

Philips scd469 Manual

8
Zoom out
Zoom in
Previous page
1/188
Next page
Mains operation
1 Put the small plug in the socket on the baby unit and insert the adapter in a wall socket.
(Fig. 3)
Battery operation
The baby unit runs on four 1.5-volt R6 AA batteries (not included). We strongly advise you to use
Philips LR6 PowerLife batteries.
Make sure your hands and the unit are dry when you insert the batteries.
1 Undo the screw of the battery compartment lid with a screwdriver and remove the lid.
(Fig. 4)
2 Insert four 1.5V AA batteries.
Make sure the + and - poles of the batteries point in the right direction.
3 Put the battery compartment lid back on the appliance and fasten the screw with a
screwdriver. (Fig. 5)
Note:Do not mix old and new batteries.
Note:Remove the batteries if you do not intend to use the baby unit for a month or more.
Note:If the batteries are in the unit when you operate it on mains power, check them for leakage every
six months.
Note:When the batteries are low, the battery symbol
à on the display and the power light blink. When
the batteries are empty, the power light and the display do not go on at all.
Parent unit
The parent unit has a rechargeable battery pack and can be recharged in the charger. When the
battery pack is fully charged, you can use the parent unit cordlessly for up to 12 hours.
1 Put the small plug into the socket of the charger and put the adapter in a wall socket. (Fig. 6)
2 Place the parent unit in the charger. (Fig. 7)
The charging light starts to burn red.
3 Leave the parent unit in the charging base until the battery pack is fully charged.
It takes at least 14 hours to charge the battery pack fully.
The charging light burns red as long as the parent unit is in the charger, even when the battery
pack is fully charged.
Note:When the battery pack is low, the power light and SYSTEM CHECK light blink. When the power
light and SYSTEM CHECK light do not go on at all, the battery pack is empty.
Note:You can also leave the parent unit in the charger to run it from the mains.
Preparing for dial-up mode
Baby unit
1 Follow the instructions above to prepare the baby unit for mains operation.
2 Insert one connector of the telephone cable supplied in the appropriate plug. Insert the plug
in the wall telephone socket.
3 Insert the other connector of the telephone cable into the phoneline-in socket of the baby
unit. (Fig. 8)
If you want your telephone to work while the baby unit is in dial-up mode, insert the cable of
the telephone in the phoneline-out socket of the baby unit.
,
,
-
-
-
ENGLISH8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips scd469 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips scd469 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info