The Jet Clean System has an automatic cleaning program. When you press the on/off button, the Jet Clean System starts cleaning in the
automatic cleaning program.
Fill the cleaning chamber before rst use.
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
,The holder automatically moves to the highest position.
3 Simultaneously press the release buttons on both sides of the cleaning chamber (1). Then lift the Jet Clean System off the cleaning
chamber (2). (Fig. 28)
,The cleaning chamber remains behind.
4 Unscrew the cap from the bottle with cleaning uid.
5 Fill the cleaning chamber with HQ200 cleaning uid to a level between the two lines (Fig. 29).
6 Place the Jet Clean System back onto the cleaning chamber (Fig. 30).
Make sure the release buttons click back into place.
Note: If you use the shaver with shaving foam or shaving gel, we advise you to rinse it under the hot tap before you clean it in the Jet Clean System. This
guarantees an optimal lifetime for the cleaning uid.
1 Place the shaver upside down in the holder with the display pointing towards the front of the Jet Clean System (Fig. 18).
2 Press the shaver tightly into the holder to lock it into place (Fig. 19).
,The display shows that the shaver is charging (see chapter ‘The display’).
3 Press the on/off button on the Jet Clean System to start the cleaning program. (Fig. 31)
,The shaver display stops showing the charging indication.
,The cleaning light starts to ash and the shaver is automatically lowered into the cleaning uid (Fig. 32).
,The cleaning light ashes throughout the cleaning program, which takes a few minutes.
,During the rst phase of the cleaning program, the shaver automatically switches on and off several times and moves up and down.
,During the second phase of the cleaning program, the shaver is placed in the drying position, indicated by the ashing drying symbol.
This phase takes approx. 2 hours. The shaver stays in this position until the end of the program. (Fig. 33)
,After the cleaning program, the charging indication appears on the shaver display (see chapter ‘The display’).
Note: If you press the on/off button of the Jet Clean System during the cleaning program, the program aborts. In this case, the cleaning or drying light
stops ashing and the holder moves to the highest position.
Note: If you remove the adapter from the wall socket during the cleaning program, the program aborts. The holder remains in its current position. When
you put the adapter back into the wall socket, the holder moves to the highest position.
-When the cleaning uid drops below the minimum level, the ‘cleaning chamber empty’ symbol starts to ash and the holder returns to its
starting position (Fig. 34).
-If you use the washing machine to clean your shaver every day, you need to rell the cleaning chamber approx. every 15 days.
Clean the cleaning chamber every 15 days.
You can wipe the outside of the Jet Clean System with a damp cloth.
1 Simultaneously press the release buttons on both sides of the Jet Clean System (1). Then lift the Jet Clean System off the cleaning
chamber (2). (Fig. 28)
,The cleaning chamber remains behind.
2 Pour any remaining cleaning uid out of the cleaning chamber. (Fig. 35)
You can simply pour the cleaning uid down the sink.
3 Rinse the cleaning chamber under the tap (Fig. 36).
The cleaning chamber is not dishwasher-proof.
4 Fill the cleaning chamber with HQ200 cleaning uid to a level between the two lines (Fig. 29).
5 Place the Jet Clean System back onto the cleaning chamber. (Fig. 30)
Make sure the release buttons click back into place.
Make sure the appliance is switched off.
1 Pull the shaving head holder off the bottom part of the shaving unit (Fig. 26).
2 Slide the green retaining frame in the direction of the arrows indicated of the retaining frame (Fig. 37).
3 Lift the retaining frame out of the shaving head holder. (Fig. 38)
4 Remove the cutter from the shaving guard (Fig. 39).
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Philips RQ 1160 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Philips RQ 1160 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.
The manual is 3,81 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
